User manual AEG-ELECTROLUX 92558G-M

[. . . ] 92558 G AU Instruction Booklet Gas Hob 2 Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine. [. . . ] 470 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240 V 50 Hz supply APPLIANCE GAS SUPPLY: Natural gas 1. 0 kPa - Universal LPG 2. 75 kPa Instructions for the Installer 11 TYPE OF GAS TYPE OF BURNER NOZZLE MARKS 1/100 mm 157 150 111 89 97 93 71 55 NOMINAL GAS CONSUMPTION MJ/h 13. 00 11. 00 6. 80 3. 80 13. 00 11. 00 6. 30 3. 80 NOMINAL PRESSURE kPa NATURAL GAS Triple Crown Rapid (large) Semi-rapid (medium) Auxiliary (small) Triple Crown Rapid (large) Semi-rapid (medium) Auxiliary (small) Dia. Tap By-pass 1/100 mm 1. 00 U-LPG 2. 75 Burner Auxiliary 28 Semi-rapid 35 Rapid 42 Triple crown 42 Aeration adjustment none 12 Important safety requirements Important safety requirements This hob must be installed by qualified personnel, according to the manufacturer's instructions and to the relevant Australian Standards. The hob should not be installed in a bed sitting room with a volume of less than 20 m3. If it is installed in a room of volume less than 5 m3 an air vent of effective area of 110 cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no air vent is required. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3. Location Choose a location free of draughts and open doors and clear of combustible materials or other fire hazards such as curtains, etc. The location should ensure convenience of operation and service. The hob may be located in a kitchen, a kitchen/diner or a room frequently occupied by people, but not in a bathroom or shower room. Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm. between the rear edge of the hob and the wall. must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm. must be allowed from the edges of the hob. The minimum distance combustible material can CLEARANCES REQUIRED WHEN FITTING THE CLEARANCES REQUIRED WHEN FITTING THE be fitted directly above GAS HOB WITHOUT A COOKER HOOD ABOVE GAS HOB WITH A COOKER HOOD ABOVE the hob is 700 mm. 700 mm 700 mm 700 mm 400 mm 50 m 55 m mm 400 mm 400 mm 55 m mm 50 m 400 mm 100 mm 50 m m 100 mm 50 m m Installation 13 Installation Important This appliance must be installed by qualified personnel. The installer shall verify the satisfactory operation of the ignition system on all burners both individually and in combination. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Regulations This appliance shall be installed in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, AS5601 (AG601) and any other relevant statutory regulations. Data label The data label is located on the bottom of the hob. This appliance is suitable for Natural or Universal LPG. Ensure that the gas supply matches the data label. The pressure test point is located on the regulator. The pressure should be measured and adjusted with the Wok burner on high flame; · that the automatic ignition system is operating satisfactory on all burners, both individually and in combination; · that the burners operate correctly, are stable, without yellow tipping or excessive noise on high and low flame. Then demonstrate to the customer the appliance operation and leave these instructions. A) End of shaft with nut B) Washer C) Elbow Electrical connections 15 Electrical connections The appliance is designed to be connected to 230-240 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. [. . . ] 9 If you are required to transport the appliance to the Company or its service agent, you must ensure it is securely packed and insured. The Company does not accept any responsibility for loss or damage of the appliance prior to it being received by the Company or its service agent. 20 AEG WARRANTY - AUSTRALIA 10 This warranty does not cover loss, damage or expense to this appliance caused directly or indirectly by power surges, electrical storm damage or incorrect power current. 11 The Company (and any company related to the Company) will not be liable for any special, incidental or consequential damages or for loss, damage or expense or for personal injury or loss or destruction of property arising directly or indirectly from the use or inability to use this appliance or any of its parts. 12 This warranty applies only to the original buyer. [. . . ]