User manual AEG-ELECTROLUX 95601G-B

[. . . ] Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the hob in any way. Child Safety l l l This hob is designed to be operated by adults. Do not allow children to play near or with the hob. Children should be kept away until it has cooled. [. . . ] After cleaning, be sure to wipe dry with a soft cloth. Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM n SOLUTION u There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. 7 u u u n The gas ring burns unevenly u u If after all these checks, your hob still does not operate correctly, contact your local AEG Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to the your local Service Force Centre. When you contact the Service Force Centre, they will need the following information: 1. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5. Date of purchase CUSTOMER CARE For general enquiries concerning your AEG appliance and for further information on AEG products, contact our Customer Care Department by letter or telephone as follows: Customer Care Department AEG Domestic Appliances 55-77 High Street Slough Berkshire SL1 1DZ Tel : 08705 350 350 8 Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. IGNITION HT SPARK HEAT INPUT Rear Left Burner (semi rapid) Front Left Burner (rapid) Rear Right Burner (semi rapid) Front Right Burner (auxiliary) Burner Auxiliary Semi-rapid Rapid Aeration adjustment none Spark Generator Ispra Control's BF 50046 - 230-240V 0. 6 YA T120 Spark Gap : Fixed APPLIANCE CLASS 3 1. 9 kW (6483 BTU/HR) 2. 9 kW Natural Gas (9895 BTU/HR) APPLIANCE CATEGORY II2H3+ 2. 7 kW L. P. G. (9212 BTU/HR) 1. 9 kW (6483 BTU/HR) GAS SUPPLY Natural gas G20 / 20mbar 1. 0 kW (3412 BTU/HR) Dia. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. 12 Installation FO 0814 FO 0264 A) End of shaft with nut B) Washer C) Elbow On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. [. . . ] C. Wiring diagram N 220 240 0 1 2 3 4 2 1 L 1. IGNITOR UNIT 17 Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Brown Blue Green Yellow Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Has inlet fuse blown? NO YES Electricity supply should now be satisfactory. PLUG (with cover removed) Inlet wiring faulty. Rectify any fault. Earth Wire Green/Yellow Neutral Wire Blue SOCKET (face view) () FUSE E( ) N L Isolate appliance and carry out: B: Insulation check. Rectify any fault including replacing fuses as necessary. 18 A. [. . . ]