User manual AEG-ELECTROLUX 9600D-A-AUS

[. . . ] · The appliance is not intended for use by young children or infirm persons without supervision. · Young children should be supervised to ensure that they do not play with the appliance. · WARNING - Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock. for the installer · When used as an extractor unit, the hood must be fitted with a 150mm diameter hose. · Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125 mm reduction flange provided. [. . . ] Indicates speed 3 (LED) Indicates Intensive speed (LED). The Intensive speed runs for 5 minutes: If the hood is on when the Intensive speed is activated, the hood reverts to previous speed after 5 minutes. If the hood is off when the Intensive speed is activated, the hood will be turned off after 5 minutes. To interrupt the Intensive speed, press button A or B. Light ON/OFF H- Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds, then turn the hood back on again. 6 LED Indicator lights for verifying the saturation of filters This hood is supplied without a charcoal filter. If the hood is to be used in the recirculation mode with a charcoal filter, the saturation indicator must be activated as follows: Depress and hold the A and B buttons simultaneously for 3 seconds. Initially only the LED indicator signal for the grease filter C is activated, shortly after the LED indicator for the charcoal filter D will activate, at this point the saturation detection has been enabled. To switch off the saturation detection : depress and hold the A and B buttons for 3 seconds until the LED indicator for the active carbon filter is flashing. Led ­ Indicator for grease filter C The LED indicator for the grease filter will flash when it requires cleaning. Follow the maintenance instructions. Led - indicator for charcoal filter D The LED indicator for the charcoal filter illuminates when the filter requires replacing. This occurs after about 160 working hours from when the active carbon filter was first put into operation. Resetting the saturation indicator After cleaning or replacing the filter depress and hold the G and H buttons again for 3 seconds until the grease filter LED or the charcoal indicator LED are no longer flashing. 7 Maintenance and care · The hood must always be disconnected from the electricity supply before beginning any maintenance work. Metal grease filter · The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Open the metal grease filter · First, push the metal grease filter stop backwards, then extract the filter, pulling downwards. Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher Place grease filters in dish washer. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are Fig. When washing the metal grease filter in the dishwasher a slight discoloration of the filter can occur, this does not have any impact on its performance. · Clean the inner housing using a hot detergent solution only (never use corrosive, abrasive or flammable cleaning products). 8 Charcoal filter · The charcoal filter should only be used if you want to use the hood in its filtering function. · To do this you will need an original AEG charcoal filter (see special accessories). · Cleaning/replacing the charcoal filter Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month. The best way to clean the filter is in the dishwasher. [. . . ] When both upper components (B) are divided in the same way, the structure may be lengthened between 100 and 120 cm (between 100 and 100. 5 cm in the model with the tube). Only for extractor version · Fix the deviation plate F for the air circulation with four screws (2 x 2) on the upper part of the structure A and secure it with a tubing of suitable length (5) to the cooker hood's discharge. Only for the filter version · Ensure that the tube is long enough at the connection ring above the cooker hood (5). After selecting the preferred installation, proceed in the following manner: · Suspend the box (ensuring that the electrical connection box is on the side where the command components are to be located) and screw in the four screws (6). [. . . ]