User manual AEG-ELECTROLUX AEG 8119T

[. . . ] INSTRUCTIONS FOR THE INSTALLATION, MAINTENANCE AND USE OF THE HOOD MOD. K71 GENERAL Before installing and/or using the hood, read all of the instructions carefully. Before installing the hood, ensure that the voltage ( V ) and the frequency ( Hz ) indicated on the registration and technical data tag attached to the inside of the appliance correspond with the voltage and frequency available in the place of installation. IDENTIFICATION PLATE AND TECHNICAL DATA PLATE: The identification plate and technical data plate are inside the appliance. [. . . ] Make sure that the fixing angle is securely attached by tightening hard. Connect the ventilation hose with connecting hose "N" (Fig. Lift the casing H up to the ceiling, so that the upper, lateral holes of the casing correspond with those of the plate, and thereafter affix them using the 4 screws provided (Fig. 7) and insert it in the motor frame with the tabs L1 in the proper dowels, thereafter affixing it with the 10 screws provided (Fig. 11) is made up of a push-button panel which is situated on the front part of the hood and comprises : 3 push-buttons for motor control (first, second and third gear) 1 push-button for illuminating light; 1 push-button indicating motor off; If the commands panel is made up of electronic commands, consult the attached instructions sheet. MAINTENANCE Before carrying out any operation, always make sure that the omnipolar switch is in the 0 (OFF) position. a) Cleaning Clean the external parts with a non-corrosive liquid detergent. Avoid using abrasive powders or brushes. b) Changing the light bulb Before replacing the light, make sure that the appliance is not powered up (position 0 (OFF) of the omnipolar switch). Extract the antigrease metal filters (Fig. In the case of a halogen lamp, before replacing the lamp, remove the support ring of the glass by means of a screwdriver. Replace the halogen lamp using only spare-parts with a G4 20W max. Remount the glass protection, attaching it with the suitable ring. In the case of dichroic 12V halogen lamp, replace the lamp using only spare-parts with a GU5. 3 20W max. In the case of a 230V halogen lamp, replace the lamp using only spare-parts with an E14 50W max. Re-install the anti-grease metal filters. d) Cleaning the metal anti-grease filter. The saturation of grease residues in the metallic filter could cause an increase in inflammability of the system. In order to prevent possible fires, the metallic filter must be washed according to its use or at least every three months in a dishwasher or in hot water with normal dishwasher detergent. After it has been well rinsed and dried, re-install the anti-grease metallic filter in its dedicated seat. REMARKS The cleaning must be carried out in accordance with the manufacturer's instructions, especially with regard to the deposits on the dirty surfaces, against a possible risk of fire. Pay careful attention that the hot-plates are always covered in a manner which does not cause the filter to overheat and to catch fire. [. . . ] FROM NOW ON EVERY 120 HOURS OF USE THE MICROPROCESSOR INDICATES THAT THE CARBON FILTER SHOULD BE REPLACED WITH A FLASHING «C» ON THE DISPLAY. THIS CONSENTS THE EXHAUST TO FUNCTION BETTER AND IMPROVES HYGIENE IN THE ROOM. TO CANCEL THE WARNING MESSAGE AFTER REPLACING THE CARBON FILTER, SWITCH OFF THE HOOD, PRESS AND HOLD KEY NO. WHEN THE KEY IS PRESSED THE LETTER «C» APPEARS ON THE DISPLAY AND AFTER 5 SECONDS THIS DISAPPEARS AND THE MICROPROCESSOR STARTS A NEW 120-HOUR COUNT-DOWN BEFORE DISPLAYING THE NEXT WARNING MESSAGE. DIE AUF IHRER ABZUGSHAUBE INSTALLIERTEN ELEKTRONISCHEN STEUERUNGEN SIND MIT MEHRFACHEN FUNKTIONEN AUS-GESTATTET: MOTORFUNKTION ON-OFF DURCH DAS DRÜCKEN DER TASTE 1 SCHALTET SICH DER MOTOR EIN ODER AUS. [. . . ]