User manual AEG-ELECTROLUX BRATOFENB60T-SBGB

[. . . ] Conservare per ulteriore consultazione. BETRIEBSANWEISUNG WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handha-bung des Gerts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, da Sie alle Anweisungen verstanden haben und gut aufbewahren. HASZNLATI TMUTAT Jtllst vllalni csak rendeltetsszeren hasznlatba vett gpekre tudunk. Krj hogy a gp hasznlatba vtele eltt gondosan olvassa el a kezelsi utastsokat. MANUEL D'INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d'utiliser cet appareil, veuillez lire atentivement les instructions et assurez-vous de les avoir comprises. Conservez les instructions pour rfrence ultrieure. EXEIPIIO XEIPIMOE HMANTIKE HPOOPIE: oxx v x ov v xvo v o v x u v u u v. HANDLEIDING BELANGRIJKE IMPORTANTS: Lees deze handleiding aandachtig en zorg dat u ailes begrijpt alvorens de kettingzaag te gebrulken en be-waar ze voor toekomstige raadpleging. BRUKERHNDBOK VIKTIG INFORMASJON: Les disse anvisningene nye og forsikre deg om at du forstr dem fr du bruker enheten og oppbevar dem for sen-ere bruk. INSTRUKCJA OBSUGI PL Gwarancja traci wano w przypadku uywania urzdzenia do celw innych ni wymienione w instrukcji obsugi. [. . . ] Do not let the blade cut in the risk sector to prevent kickback. 15 C. Description of the safety devices on the machine 1234 Safety lever The guard covers the sharp extremities of the blade when the machine is in the resting position for transport or storage. Safety guard Never use the machine with its Safety lever pressed with adhesive tape, string or other. This device serves to prevent accidentally pressing the throttle trigger (fig. 3), can only be pressed if the safety lever is pressed at the same time (fig. By means of 2 separate springs, upon releasing the grip, the throttle trigger (fig. 17) return automatically to their original positions. Antivibration device The machine is equipped with an antivibration device which serves to reduce the vibrations transmitted to the operator. Engine stop device Turn the stop button Stop (fig. To make sure this button works properly, start the engine and check that it stops when the Stop button is turned to the Stop position. Protection for transport 1 2 3 4 10 This very important safety device (fig. Double Handle Adjust and secure double hand clamp by tightening the screws. Fitting guard on line cutter head and grass cutting blade Fit the safety guard (A) against the gearbox (I) and the upper clamp (F) over the shaft. The string cutting blade housed in the plastic shield will cut the nylon string to optimum length; a string that is too long reduces the rotation speed of the engine and interferes with cutting efficiency, as well as increasing the risk of injury. Apply the string cutter blade (L) and fasten it with the screw (E). Assembly/disassembly of line cutter head 2 3 4 10 Apply the nylon string head as shown in the illustration: 1) Protection flange 2) Upper plate 3) Protection (nylon string head B) 4) Nylon string head. As ENGLISH - 5 234 you tighten, hold the nylon string head and plate still and insert the wrench or screwdriver supplied in the holes in the plate and gearbox; first turn the plate until the two holes match. Assembly/disassembly of grass cutter blade Lower washer - e) Spacer - f) Rotating mower gauge - g) Blade locking screw (length mm 34, 5). Assembly of sawtooth blade and blade guard 2 3 4 10 When using the sawtooth blade, remove the guard for the line cutter head and grass cutting blade and replace the flange guard (A) with the sawtooth blade guard (H). Saw tooth blades (24 - 80 tooth) have a central base diametre of 20mm and therefore require the use of the appropriate size top flange to ensure a correct fit. The part number is detailed in the cutting attachment summary chart. For assembly see figures (E7, E8). 2 3 4 10 Assemble blade as illustrated: a) Flange guard b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Fixed mower gauge - f) Blade locking screw (length mm 16). [. . . ] The sawtooth blade serves to cut bushes and small trees, with maximum diameter of seven centimeters. Rest the left side of the special shield on the trunk while cutting to limit the risk of losing control of the machine. L. Environmental information This section contains information useful for maintaining the characteristics of eco-compatibility included in the origin design of the machine, and as regards proper use and disposal of oil and fuel. Design In the design stage, care was taken to develop an engine with reduced consumption and low emissions of noise and pollutant exhaust fumes. [. . . ]