User manual AEG-ELECTROLUX C2060D-M

[. . . ] 2060 D Cooker hood Operating and Installation Instructions Contents Safety warnings For the User For the Installer Description of the Appliance Extractor version Filter Version Control Panel Maintenance and care Cleaning the hood Metal grease filter Removing the metal grease filter Charcoal filter Changing the light bulb What to do if Service and Spare Parts Guarantee Conditions Technical Specifications Mounting accessories included Electrical connection Safety warnings for the electrician Wall unit mounting 3 3 3 5 5 5 6 8 8 8 8 9 10 11 12 13 15 15 16 16 17 Printed on recycled paper AEG - putting words into action 2 Safety warnings For the User · The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. · Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. · Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. [. . . ] Follow the maintenance instructions. Led - indicator for charcoal filter D The LED indicator for the charcoal filter illuminates when the filter requires replacing. This occurs after about 160 working hours from when the active carbon filter was first put into operation. Resetting the saturation indicator After cleaning or replacing the filter depress and hold the G and H buttons again for 3 seconds until the grease filter LED or the charcoal LED are no longer flashing. 7 Maintenance and care · The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood · Clean the outside of the hood using a damp cloth and a mild detergent. · Never use corrosive, abrasive or flammable cleaning products. · Never insert pointed objects in the motor's protective grid. · Only ever clean the switch panel and filter grille using a damp cloth and mild detergents. · It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter · The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external ducted or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Open the metal grease filter · Pull the spring-lock and extract the grease filter. 3 Hand washing Soak grease filters for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. 8 Dishwasher Place grease filters in dishwasher. Select the most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. Charcoal filter · The charcoal filter should only be used if you want to use the hood in its filtering function. · To do this you will need an original AEG charcoal filter. · Replacing the charcoal filter The charcoal filters cannot be cleaned, we recommend that they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. · Fitting Fit the charcoal filter first rearward on the long supporting tongue, then rotate it to close the motor housing and fix it using its two red keys A. · To remove proceed in the reverse order. · Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. · The charcoal filter can be ordered from your local AEG Service Force Centre. A A Fig. 4 9 Warning · Failure to observe the instructions on cleaning the unit and changing the filters could cause a fire hazard. You are therefore strongly recommended to follow these instructions. [. . . ] - The product is installed taking into account regulations in your new country. 13 Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nürnberg Pordenone Stockholm Slough +33 (0) 44 62 29 29 +49 (0) 800 234 7378 +39 (0) 800 117 511 +46 (0) 8 672 5360 +44 (0) 1753 219899 14 Technic Details Models Dimensions - extractor ver (in cm): Height Width Depth 2060 D 81-126. 5 89, 8 51 Dimensions - filter version (in cm): Height 81-136 Width 89, 8 Depth 51 Maximum absorbed power: Motor absorption: Lighting: Length of the cable: 215 W 1 x 130 W 4 x 20W 150 cm Mounting accessories included 6 wall plugs Ø 8 mm 6 wood-screws 5 x 45 mm 2 metal screws 2, 9 x 13 4 metal screws 3 x 9 2 hooks 1 chimney support 1 deflector 1 reduction flange Ø 125-120 mm 15 Electrical connection Safety warnings for the electrician The electric outlet should be placed inside the chimney. The hood has a power cable, 150 cm, with earth connection and the rated voltage is 220 - 240 V. Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. [. . . ]