User manual AEG-ELECTROLUX C88000M-MNAG3

[. . . ] Juli 2001 2:15 14 C88000M Induktions-Glaskeramik-Kochfeld Table de cuisson vitrocéramique à induction Piano di cottura in vetroceramica induttivo Induction Glass Ceramic Cooking Surface Montage- und Gebrauchsanweisung Mode d'emploi et instructions de montage Istruzioni di montaggio e per l'uso Installation and Operating Instructions 947344. book Seite 86 Mittwoch, 11. Juli 2001 2:15 14 Dear Customer, Please read these operating instructions through carefully. Above all, please take note of the "Safety" section on the first few pages. Please keep these operating instructions for future reference. [. . . ] If the cooking zone is switched on without a suitable pan on it f flashes in the digital display of the cooking zone. After about 10 minutes the cooking zone switches itself off automatically. heating up a pan that is empty) or with faults in the electronics the display j is lit. The cooking zone switches itself off automatically. To be able to use it again the cooking zone must have been first switched off and then reset to the required heat setting. 97 947344. book Seite 98 Mittwoch, 11. Juli 2001 2:15 14 Operating Instructions Before Using for the First Time Initial Cleaning 0 Wipe the glass ceramic cooking surface with a damp cloth. Important: Do not use any caustic, abrasive cleaners!The surface could be damaged. 1 98 947344. book Seite 99 Mittwoch, 11. Juli 2001 2:15 14 Operating Instructions Using the Cooking Zones Cooking Zone Switches With the cooking zone switches you have a choice of setting the heating capacity to 14 steps (with intermediate settings) 1 = the lowest capacity 9 = the highest capacity A = Automatic P = power function You can select intermediate settings in the ranges 2 to 7. In the digital display these are marked with a top left dot. Activating the Power Function To switch the power function on (*only provided for cooking zone 1, front left ø 210 mm) turn the cooking zone switch up to the stop and then back to stage 9 and then let go. A P appears immediately in the digital display on the glass ceramic surface. 9 is displayed in the cooking stage display next to the switch. 3 1 The booster function is activated at the most for 10 minutes. Then the cooking zone switches automatically to cooking stage 9. The power function may not be used or is deactivated if the rear left cooking zone Ø 145 mm is on or set to heat setting 8 to 9, since otherwise the total heating capacity of both cooking zones together would exceed the limit. After 3 seconds P changes to 9 in the digital display. 99 947344. book Seite 100 Mittwoch, 11. Juli 2001 2:15 14 Operating Instructions Cooking without the Automatic Feature 0 1. For heating up/browning, select a high power. 2. As soon as steam starts to form or the oil is hot, turn back to the heat setting necessary for further cooking. To stop cooking, turn back to the zero position. 2 Note: When cooking with the induction cooking zone you should take into account that ­ the heating up times are reduced by the direct energy transfer to the pan!­ the cooking process stops immediately after the cooking zone is switched off (no boiling over!). Cooking with Automatic Heating Up This automatic feature operates at its full capacity (9) for a given time and then automatically switches down to the set further cooking stage. The duration of the automatic heating up boost depends on the selected further cooking stage. Turn the cooking zone switch to the right to the stop A. [. . . ] · All cut surfaces are to be sealed with a suitable sealant for protection against moisture. · On tiled work surfaces, the joints in the area where the hob sits on the surface must be completely filled with grout. · On natural, artificial stone, or ceramic tops, the snap action springs must be bonded in place. · Ensure that the seal is correctly seated in the frame and that it is seated against the work surface without leaving any gaps. [. . . ]