User manual AEG-ELECTROLUX C9500G-M

[. . . ] - 90/396/EEC regarding "Gas appliances" - 89/109/EEC regarding "Materials in contact with food" - Moreover the above mentioned Directives comply with Directive 93/68/EEC. - This household appliance has been designed for cooking and it must therefore be used for this purpose only. IN CASE OF FIRE: · In case of fire, close immediately the main valve of the gas pipe line, disconnect current and never pour water on firing oil in any case. · Do not store flammable products or aerosol containers near the burners, and do not vaporize them near lighted burners. DEAR CUSTOMER, · Carefully read these instructions before using the appliance and keep them for future consultation. · Keep potentially hazardous packaging (plastic bags, polystyrene etc. ) out of the reach of children. FOR YOUR SAFETY AND THE ONE OF YOUR CHILDREN. [. . . ] Below you will find an indicative cooking table (TAB. C). C 0 17 1 2 3 4 140 Ø Ø GB Fig. 6 A M H P 1 G I 2 R G F 3 8 Fig. D 480 mm mm 240 second level SURFACE BAKING GRILL (480x240) NOTE: The grill must be used with the door half-open (see fig5 A). Fit the deflector S onto the centring pins N on the top of the oven opening (fig. 5 B ). Then gently close the oven door against the deflector. 140 Use of the electric grill with the oven door closed Some models are designed for the grill to be used with the oven door completely closed. In this case the deflector S shown in fig. 5 B 0 25 N S USE OF THE TURNSPIT For the functions of the turnspit turning the knob on the position (fig E) or on the symbol (fig C) when the thermostat is separate or, in some models, press the marked button with the symbol . TURNSPIT multilpe For utilization of the turnspit follow the instructions described. - Thread the chicken or the cubes of meat for roasting on the spit L , ensuring that it is gripped safely between the two forks F and balancing it properly to avoid unnecessary strain on the trasmission R (fig 6). - Put the spit on the support G, after having introduced its opposite end in the socket P of the transmission R (fig 6) - Put the support G completely into the oven so that the bar I goes into the socket H of the turnspit motor M (fig 6A). Referring to the pertinent spare parts, apply to the appliance's supplier. The manufacturer declines all responsibility for any damage to persons or things caused by failure to observe the rules indicated above. F B II X III IX L A IV VIII 10 15 20 1 Time of the day 2 Timing and insertion 3 Signal timng and insertion L B R L F N ELECTRICAL CONNECTION Connection of the appliance to the power mains should be done by a licensed electrician familiar with local safety regulations. 6 A 6 35 30 25 V Fig. 9 VI VII A5 B5 N S R P F L S G Applance type Aii gas All gas + elett. grill Supply single-phase 230 V~ Type of cable section Rubber H05 RR-F 3 x 0, 75 mm2 3 x 2, 5 mm2 Rubber H05 RR-F REPLACEMENT OF THE CABLE In case the cable is damaged, replace it in accordance with the following instructions: - open the box of the supply board as described on the picture below; - unscrew screw "A" fixing the cable; - replace the cable with one of the same lenght and in accordance with the features described on the table; switch the appliance off, and close the gas tap - the `green-yellow" earth wire must be connected to the terminal " " and it must be about 10 mm longer thean the live wires; - the "blue" neutral wire must be connected to the terminal marked with letter "N"; - the live wire must be connected to the terminal marked with letter "L". 5 55 50 45 40 E A M H P G I R G GB XI XII I CARE AND MAINTENANCE INSTRUCTIONS DESTINED TO THE USER II X Before cleaning the appliance, disconnect the gas general tap and unplug the appliance or disconnect power at the main circuit breaker of the electrical system. Do not clean the appliance surfaces when still hot. III IX OVERALL DIMENSIONS IV VIII 1450/1500 N ENAMELLED SURFACES Clean with a damp sponge using soap and water. Grease can be easily removed using hot water or a specific cleansing agent for enamelled surfaces. Do not leave any acid or alkaline substances (lemon juice, vinegar, salt, etc. ) on the enamel. Clean the parts in stainless steel with specific cleansers for stainless steel surfaces. These detergents must be applied using a soft cloth. 895 610 GRIDS AND BURNERS To clean the work-top burners, remove them by pulling upwards and soak them for about 10 minutes in hot water with a little detergent. After having cleaned and washed them, wipe them carefully. Make sure that no burner hole is clogged. [. . . ] For butane/propane gas, the adjusting screw must be tight screwed. Make sure that the flame does not extinguish passing quickly from the maximum flow to the minimum flow, and closing and opening the oven door (the oven door must be closed softly). Attention: for taps with safety device, the minimum adjusting screw "T" is on the outside of the tap rod (fig. I ). T DISASSEMBLE OF WORK-TOP In case it is necessary to repair or replace the inside components, act as follows:remove the glass lid from its position slipping off it upwards. [. . . ]