User manual AEG-ELECTROLUX CDW200

[. . . ] Contents For the User Safety instructions Information de sécurité General advice Damage in transit Applications Protecting the machine against freezing 3 4 5 5 5 5 Operating instructions Test the machine by running a cycle 6 Care and cleaning Rinse conditioner dispenser Spray arm Coarse strainer Fine filter Detergent dispenser Cleaning 7 7 7 7 7 7 7 Loading Controls and programme table In the event of a fault Trouble shooting list 8 9 13 13 Service and spare parts 14 For the Installer Installation Countertop Use 10 10 Positioning Water supply Discharge connection Electrical connection Built-In Use 10 10 10 10 11 Installation Tips Water supply Discharge connection Electrical connection 11 11 12 12 Technical data 14 -2- Safety instructions Please read all instructions before using your dishwasher. Use your dishwasher only as instructed in this Use and Care Manual. Installation and grounding instructions are included with your new diswasher for the installer´s reference. · To avoid entrapment and/or suffocation, remove the door from any dishwasher that is discarded or otherwise not in use. [. . . ] Start the dishwasher by turning the programme knob to the start position. 5. Check the strainers to see whether they need cleaning when the dishwasher has finished the wash. -6- Care and cleaning 1 2 3 4 5 Rinse conditioner dispenser (1) Use of a rinse conditioner will result in cleaner and faster drying of the load, since it helps water and soil to run off. Too much conditioner may result in streakiness, too little may cause white spots. This is enough for 40-70 wash cycles, depending on the dosage setting. When the rinse conditioner level is approaching the bottom of the scale it is time to refill the dispenser. Swivel out the filler trough and carefully fill up with rinse conditioner until the level reaches the red mark on the level indicator tube. Do not overfill, and carefully wipe off any spillage to prevent sudsing problems. Don't forget to close the filler trough afterwards. Adjust the dosage setting according to the hardness of the water. Begin with the lowest dosage setting and increase as necessary by turning the arrow clockwise. Do not fill the rinse conditioner dispenser with liquid detergent. Coarse strainer (3) The purpose of the coarse strainer is to catch large objects such as toothpicks and pieces of eggshell. Make sure that the strainer is always clean. Lift it out and rinse it under running water whenever necessary. Fine filter (4) It is just as important to keep this filter clean. A dirty or clogged filter will always impair washing efficiency. The fine filter can easily be removed for cleaning when you have removed the coarse strainer. Detergent dispenser (5) For a normal load pour about 1-2 tablespoons of granular dishwasher detergent on the inner door. Cleaning If hard water causes lime deposit buildup, e. g. on the heating element, follow these instructions: 1. After dishwasher begins to fill, open door and pour 1/4 cup of white vinegar into dishwasher. Run through the full cycle. Spray arm (2) It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. If the spray arm needs cleaning, unscrew the nut clockwise (left-hand thread) and lift off the spray arm. Clear the holes and shake out any food remnants. -7- Loading How to load the dishwasher The illustration shows the machine loaded with five place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. [. . . ] Use a drain hose clamp (not included) to connect the hose to the sink drain or disposer. Entry direct into the sink drain must be above the trap. "Y" Branch Tailpiece Drain hose hole Connection to Sink Drain Electrical connection The dishwasher must be connected to an grounded wall socket, preferably on a separate circuit protected by a 15 amp fuse or circuit breaker. Only after the dishwasher has been positioned inside its enclosure, secured and hoses connected should electrical connection be made. max 465 mm - 12 - In the event of a fault Trouble shooting list · If water leaks from the machine · Turn off the water supply tap or stopcock immediately and isolate the machine from the electrical supply by removing the plug from the wall socket. · Check that all seals, seams and connections are watertight. There is always a certain risk of leakages in any machine connected to a water supply, no matter what water safety features it may have. [. . . ]