User manual AEG-ELECTROLUX CHDD8795M-GB

[. . . ] Failure to do so could cause grease deposits to build up, resulting in a fire hazard. For the installer · When used as an extractor unit, the hood must be fitted with a 150mm diameter hose. · Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125 mm reduction flange provided. In this case the hood will be slightly noisier. · When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ring surfaces: electric cookers 300 mm gas cookers 300 mm coal and oil cookers 400 mm min. [. . . ] 3 Depress the control ball towards the top : once for submersed lighting, once again for full lighting, depress again to switch off the light. Control device for grease or charcoal filter The air duct, in this hood, is provided with a device that signals when the filter requires cleaning or changing . depress towards the top to switch on the lights Fig. 3 Led signal for grease filter The LED signal flickers (flickering green light) when the grease filter requires cleaning, occurs at about 40 operating hours. Carefully note the device for grease filter maintenance! Led signal for charcoal filter The LED signal flickers (flickering orange light) when the grease filter requires cleaning, occurs at about 160 operating hours. Carefully note the device for charcoal filter maintenance! Re-setting the saturation signal After cleaning or replacing the filter, select the intensive speed (the control ball lights up with a red flashing light), depress again and hold depressed for about 3 seconds until a `bip' sound indicates the reset. 58 Maintenance and care · The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood · Clean the outside of the hood using a damp cloth and a mild detergent. · Never use corrosive, abrasive or flammable cleaning products. · Never insert pointed objects in the motor's protective grid. · Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. · Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. · It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter · The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. · To access the grease filter, first remove the frontal Extract screens which conceal the grease filter. Removing the frontal screens: Extract the small screen, rotate upwards and unhook. Repeat the operation for all the small screens. 4 59 Removing the metal grease filter Pull the handle downards, then extract the filter. Fig. 5. Handle Bild 3 Hand washing Soak grease filters for about one hour in hot water with a greaseFig. 5 loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. [. . . ] · Hang the hood (4) adjust its position (5-6) and from the inside of the hood sign two points for definitive fixing (7), remove the hood and drill two holes Ø 8mm (8), fit two wall plugs, hang the hood again and fix it definitively with two screws (9). Cover the drill holes for screws with the two screw caps provided. 4 4 6 5 5 3 7 8 6 8 2 1 9 Fig. 9 67 · Fix the sides of the cooker hood by 11 fastening the pins (10a) to the sides of the fastening screws (10b). Only DD 8794: side panels are available as a special accessory 10a please contact your local Service Force Centre (or see paragraph "Special Accessory"). [. . . ]