User manual AEG-ELECTROLUX CHDI8820-A

[. . . ] HI 8820 CHDI 8820 Dunstabzugshaube Afzuigkap Hotte Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruiksaanwijzing Notice dutilisation et dinstallation Operating and Installation Instructions Contents Safety warnings For the User For the Installer Description of the Appliance Extraction Recirculation Control Panel Control device for grease and charcoal filters Grease filter LED (D) Charcoal filter LED (E) Resetting the saturation indicator Maintenance and care Cleaning the hood Metal grease filter Removing the metal grease filter Charcoal filter Changing the light bulb What to do if Special accessories Technical assistance service Technical Specifications Mounting accessories included Electrical connection Safety warnings for the electrician Installation 62 62 62 64 64 64 65 66 66 66 66 67 67 67 67 68 69 70 70 71 72 72 73 73 74 Printed on recycled paper AEG - putting words into action 61 Safety warnings For the User The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. [. . . ] Never insert pointed objects in the motors protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filter First, push the metal grease filter stop (f1) backwards, then extract the filter (f2), pulling downwards. f1 Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. f2 Dishwasher Place grease filters in the dishwasher. 4 most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). 67 Charcoal filter The charcoal filter should only be used if you want to use the hood in the recirculation function. To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). Cleaning/replacing the charcoal filter Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month (when using the hood 2, 5 hours per day, in avarage). The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. [. . . ] Insert and tighten another 2 screws in the remaining free holes (8) for secure fixing. Carry out the electrical connection (9) to the mains power supply, only turn on the power supply upon completion of assembly. Hook the hood onto the support (10) , ensuring it fits properly to hook the hood onto the support partially tighten 4 screws (see also step 12). Secure the hood to the support using 6 screws (11); this will also help centre the two sections. [. . . ]