User manual AEG-ELECTROLUX DB 510

[. . . ] Please check the mains cord from time to time for damage!Special tools are required to repair a damaged mains cord. To repair this or any other fault please contact your specialist dealer or your local customer service centre. Electrical appliances may only be repaired by qualified specialists. [. . . ] You will find which temperature setting (fabric Dry Ironing 0 Set the steam switch (Figure 1/F) to position "0" (Figure 4/A). 0 Turn the temperature selector (Figure 1/O) to the desired temperature. 14 g type) matches which steam setting in the ironing table. As soon as the iron is held horizontally steam begins to form. When the iron is set upright again the steam supply stops automatically. 0 Now press the steam jet button (Figure 1/H). Wait at least 5 seconds before pressing the button again. 1 Spray function (Figure 6/A) The first time you use the appliance, or if you have not used it for a long time, you will need to press the spray button (Figure 1/G) several times before water comes out of the spray nozzle (Figure 1/D). You can also use the spray function when dry ironing. Important: Do not attempt to freshen up clothing whilst it is still being worn. Risk of burns! Drip stop (not DB 7020) The steam iron is fitted with an automatic drip stop. The drip stop interrupts the formation of steam immediately if the selected temperature is too low. Super steam jet function (Figure 6/B) The super steam jet is of valuable assistance when ironing, for example, creases, embroidery etc. You can trigger the additional steam jet both when steam ironing and when dry ironing. Set the temperature selector (Figure 1/O) to the "MAX" position and wait until the correct temperature has been reached, i. e. , until the power indicator (Figure 1/J) goes out. Set the steam switch (Figure 1/F) to position "0" (Figure 4/A). Fill the water reservoir (Figure 1/P) to the "MAX" mark. Set the temperature selector (Figure 1/O) to "MAX". Wait until the power indicator (Figure 1/J) goes out. Set the steam switch (Figure 1/F) to the "Self Clean" position (Figure 4/C) and hold it firmly in place. Steam and hot water will now run out of the steam exit holes (Figure 1/C). Move the iron gently to and fro above the sink until the water reservoir is empty. Allow the iron to cool and wipe the soleplate dry with a soft cloth. 0 0 0 0 0 0 0 0 0 What to do, if . . . · no "Steam" appears when using on a steam setting?­ In warm, dry air (during the winter) a smaller jet of steam is normal because it is taken up by the dry air before condensing. ­ Emptying the filled water reservoir can wash out fluff. Remove the mains cord and tip the filled appliance forwards at an angle (Figure 7) so that the water can run out of the filling hole. [. . . ] Only with your support can we be sure to develop appliances to suit your needs. 17 AEG Kundendienst in Europa Deutschland Sollte dieses AEG Kleingerät wider Erwarten nicht funktionieren, senden Sie es bitte an folgende Adresse: Beginnt die Postleitzahl Ihres Wohnortes mit 2 - 3 - 4 - 5 AEG Kleingeräte-Zentralwerkstatt Firma Elektro Stefan Irsen Sachtlebenstraße 1, 41541 Dormagen Beginnt die Postleitzahl Ihres Wohnortes mit 0 - 1 - 6 - 7 - 8 - 9 AEG Kleingeräte-Zentralwerkstatt Firma Trepesch GmbH Steinstraße 500, 90419 Nürnberg In Deutschland stehen wir Ihnen für Fragen, Anregungen oder bei Problemen rund um unsere Kleingeräte und Raumpflegegeräte montags bis freitags von 8 bis 18 Uhr zur Verfügung. We will not accept claims if unauthorised modification is made or if nonstandard components are used. The appliance must be used in accordance with the operating instructions and the guarantee does not cover any damage caused during transit or through misuse. In order to establish the date of purchase, advice note or similar document must be produced whenever the guarantee is claimed. Garanzia Duranti i primi 12 mesi d'esercizio, vengono fornite gratuitamente dall'AEG le parti di ricambio riconosciute difettose. [. . . ]