User manual AEG-ELECTROLUX DD 8795

[. . . ] La distance minimale entre la surface de support des récipients de cuisson et la partie la plus basse de la hotte de cuisine doit être d'au moins 30 cm si la table de cuisson est équipée de foyers électriques. Si la hotte est un modèle de 60 cm (modèle DD 8765) : installation sur les tables de cuisson au gaz de 60 cm - distance minimale de 30 cm installation sur les tables de cuisson au gaz de 70 cm - distance minimale de 45 cm installation impossible sur les tables de cuisson au gaz de plus de 70 cm si la hotte est un modèle de 90 cm (modèle DD 8794-8795 -HD 8795) installation sur les tables de cuisson au gaz de 60 et 70 cm distance minimale de 30 cm installation sur les tables de cuisson au gaz de plus de 70 cm distance minimale de 45 cm Si les instructions d'installation du dispositif de cuisson au gaz spécifient une plus grande distance, il faut en tenir compte. When used as an extractor unit, the hood must be fitted with a hose having preferably the same diameter as the outlet hole. Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125 mm reduction flange provided (DD 8794 and DD 8795 only). [. . . ] The LED lights up in orange when the carbon filter needs to be cleaned/ replaced; this happens approximately every 160 hours of operation. Every time the cooker hood is used, check whether the L2 LED is lit. After cleaning or replacing the filters, switch on the cooker hood at any suction speed (power), then press and hold the knob for more than 3 seconds, until you hear a beep indicating that the reset procedure has been performed successfully. the L2 LED and the cooker hood both switch off. In some situations (for example, when the L2 LED is indicating that the grease filters and the carbon filter are saturated), the procedure described above must be repeated. Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Clean the outside of the hood using a damp cloth and a solution of water and mild washing up liquid. Only ever clean the switch panel and filter grill using a damp cloth and mild washing up liquid. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal recycling function. Attention: the metal grease filters must be removed and Extract washed, either by hand or in the dishwasher, every four weeks. To access the grease filter, first remove the front panels which conceal the grease filter. Repeat the operation for all the small panels. Pull the handle downards, then extract the filter. Hand washing Soak grease filter(s) for about one hour in hot water with a greaseFig. 5 loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. [. . . ] If the light does not come on, make sure the bulb has been inserted correctly before contacting your local Service Fig. Prior to touching the light bulbs ensure they are cooled down. Uk Customer Services Department Major Appliances AEGElectrolux Addington Way Luton Bedfordshire LU4 9QQ 08705 350 350 (*) * calls to this number may be recorded for training purposes. To guarantee the same quality of illumination we advise using the same type of light: Halogen Lamp PHILIPS STANDARD LINE Code 425409, 20W 30° Ø35 12V GU4 DD 8765 Dimensions (in cm): Height x Width x Depth Maximum absorbed power: Motor absorption: Light absorption: upper light side lights** Length of the cable: Electrical connection: Fuse rating: Ensure that the transparent part of the bulb is directed towards the outside to guarantee a correct diffusion of the light. [. . . ]