User manual AEG-ELECTROLUX DD8693-M

[. . . ] · Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125 mm reduction flange provided. In this case the hood will be slightly more noisy. · When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ring surfaces: electric cookers 500 mm gas cookers 650 mm coal and oil cookers 700 mm min. · The national Standard on fuel-burning systems specifies a maximum depression of 0. 04 bar in such rooms. [. . . ] Initially only the LED indicator signal for the grease filter C is activated, shortly after the LED indicator for the active carbon filter D will activate, at this point the saturation detection has been enabled. To switch off the saturation detection : depress and hold the A and B buttons for 3 seconds until the LED indicator for the active carbon filter is flashing. Led ­ Indicator for grease filter C The LED indicator for the grease filter will flash when it requires cleaning. Follow the maintenance instructions. Led - indicator for active carbon filter D The LED indicator for the active carbon filter illuminates when the filter requires replacing. This occurs after about 160 working hours from when the active carbon filter was first put into operation. Resetting the saturation indicator After cleaning the filter depress and hold the G and H buttons again for 3 seconds until the LED ­ grease filter indicator or the LED ­ active carbon indicator D are no longer flashing. 69 Maintenance and care · The hood must always be disconnected from the electricity supply before beginning any maintenance work. Metal grease filter · The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Open the metal grease filter · First, push the metal grease filter stop backwards, then extract the filter, pulling downwards. Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher machine Place grease filters in dish washer. Select most powerful washing programme and highest temperature, at least 65°C. When washing the metal grease filter in the dishwasher a slight discoloration of the filter can occur, this does not have any impact on its performance. · Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). 70 Charcoal filter · The charcoal filter should only be used if you want to use the hood in its filtering function. · To do this you will need an original AEG charcoal filter (see special accessories). · Cleaning/replacing the charcoal filter Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month. The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the charcoal, the filter should be dried in an oven for 10 minutes with a temperature of maximum 100º C. After approximately three years of use, the charcoal filter should be replaced with a new, as the odour reduction capacity will be reduced. · Mounting Remove the frame b which supports the filter c by turning 90° the two knobs a, Fig. 4. Insert the coal mattress inside the frame and put all parts back in their place d. · To dismount proceed in reverse order. [. . . ] Hang the hood (4) and adjust its position (5-6). · From the inside of the hood sign two points for definitive fixing (7). · Remove the hood (8) and drill two holes Ø 8mm (9), fit two wall plugs (10). · Drill two holes Ø 8mm on the upper side close to the ceilling, fit two wall plugs (11) (In case the hood is to be used in filter version, mount the deflector F on the chimney support with four screws 2, 9x6, 5 (2 screws for hood model DD 8623)) and fix the chimney support G with two screws (12). [. . . ]