User manual AEG-ELECTROLUX DD8765-M-CH

[. . . ] DD 8794 - DD 8795 CHDD 8795 DD 8765 Dunstabzugshaube Afzuigkap Hotte Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruiksaanwijzing Notice dutilisation et dinstallation Operating and Installation Instructions Contents Safety warnings For the user For the installer Description of the Appliance Extractor version Filter Version Control Panel Switching on the hood Switching on the light Control device for grease or charcoal filter Led signal for grease filter Led signal for charcoal filter Re-setting the saturation signal Maintenance and care Cleaning the hood Metal grease filter Removing the frontal screens: Removing the metal grease filter Charcoal filter Changing the light bulb Changing the upper light DD 8765 Changing the side light DD 8765 Special accessories Technical assistance service Technical Specifications Mounting accessories included Electrical connection Wall mounting 57 57 57 59 59 59 60 61 61 61 61 61 61 62 62 62 62 63 64 65 65 66 66 67 68 68 69 70 Printed on recycled paper AEG - putting words into action 56 Safety warnings For the user The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Always cover heating elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. [. . . ] Never use corrosive, abrasive or flammable cleaning products. Never insert pointed objects in the motors protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. To access the grease filter, first remove the front panels Extract which conceal the grease filter. Removing the front panels: Extract the small panel, rotate upwards and unhook. Repeat the operation for all the small panels. 4 62 Removing the metal grease filter Handle Pull the handle downards, then extract the filter. Fig. 5. Hand washing Soak grease filter(s) for about one hour in hot water with a greaseFig. 5 loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). After having re-installed the grease filter, remount the front panels following the instructions for removal in reverse. The narrower front panel is to be mounted at the highest position. 63 Charcoal filter The charcoal filter should only be used if you want to use the hood in the recirculation function. To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). [. . . ] Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician. Electrical connection for UK only Safety warnings for the electrician Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. The switch must be accessible at all times. [. . . ]