User manual AEG-ELECTROLUX DD8793-M

[. . . ] DD 8793 Cooker Hood Cappa aspirante Campana extractora Exaustor Operating and Installation Instructions Istruzioni di montaggio ed uso Instrucciones de montaje y manejo Manual de Instruções Contents Safety warnings for the user for the installer Description of the Appliance Extractor version Filter Version Hood Operation Switching on the hood Switching on the light Control device for grease or charcoal filter Led signal for grease filter Led signal for charcoal filter Resetting the saturation indicator Using the Remote Control Remote Control Maintenance Maintenance and care Metal grease filter Open the metal grease filter Charcoal filter Changing the light bulb Cleaning Special accessories Technical assistance service Guarantee conditions Technic Details Mounting accessories included Electrical connection Safety warnings for the electrician Wall unit mounting 4 4 4 6 6 6 8 8 8 8 8 8 8 9 9 10 10 10 11 12 13 13 13 14 15 15 16 16 17 2 Safety warnings For the user The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. [. . . ] Every status change (changing speed, switching on the lights, etc. ) and is recognizable from the variation of light emitted by the control ball and by an acoustic signal. The control ball serves also as a light signal : No signal : The hood is switched off. Static green light : Hood is switched on at power level 1 (minimum). Static orange light : Hood is switched on at power level 2 (medium). Static red light : Hood is switched on at power level 3 (maximum). Alternating red light : Hood is switched on at intensive power level (timed at 5 minutes) Alternating green light : Indicates the grease filter saturation - clean the grease filter Alternating orange light : Indicates the charcoal filter saturation - clean or replace the charcoal filter Attention!The control Ball flashes orange to indicate the saturation of the odor filter even when the charcoal filter is not installed inside the cooker hood. However perform the signal reset operation as follows: select the intensive speed (the control ball lights up with a red flashing light), depress again and hold depressed for about 3 seconds until a bip sound indicates the reset. 7 Switching on the hood - Fig. 3 The control ball is a balancer switch. Depressing the control ball repeatedly towards the right switches on the hood and you may select the suction level desired, depressing once again on the right the hood switches off. Fig. 3 depress towards the right to switch on the hood depress towards the left to switch on the light. Switching on the light Fig. 3 Depress the control ball towards the left : once for submersed lighting, once again for full lighting, depress again to switch off the light. Control device for grease or charcoal filter The air duct, in this hood, is provided with a device that signals when the filter requires cleaning or changing . Led signal for grease filter The LED signal flickers (flickering green light) when the grease filter requires cleaning, occurs at about 40 operating hours. Carefully note the device for grease filter maintenance! Led signal for charcoal filter The LED signal flickers (flickering orange light) when the charcoal filter requires cleaning or replacing, occurs at about 160 operating hours. Carefully note the device for charcoal filter maintenance! Resetting the saturation indicator After cleaning or replacing the filter, select the intensive speed (the control ball lights up with a red flashing light), depress again and hold depressed for about 3 seconds until a bip sound indicates the reset. 8 Using the Remote Control The remote control may operate in humid environments, but not when placed on wet surfaces. Selecting the Suction Speed position the remote control vertically near the cook top area and rotate clockwise to increase the suction speed, and anticlockwise to decrease the suction speed. Turning on the Light, press the remote control from the top downwards once for suffused lighting, again for full lighting, and again to turn off the light. Fig. 4 Remote Control Maintenance Clean the remote control using non abrasive detergents. Follow the instructions below in order to replace the batteries for the remote control : - Using a small screwdriver, raise the cover on the base of the remote control, in order to access the battery compartment. 5 Remove the battery holder, and replace 4 new batteries type . . 394 of 1. 5V. Place the batteries in order in the battery holder (see Fig. 5) taking care to respect the polarities indicated on the base of the upper section of the remote control. If the remote control doesnt work after installation (yet the control ball works correctly), do the following: 1. [. . . ] When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician. Electrical connection for UK only Safety warnings for the electrician Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. The switch must be accessible at all times. The following is valid in the United Kingdom only: - the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol ( ), or coloured green or green and yellow; - the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. 16 Wall unit mounting - Fig. [. . . ]