User manual AEG-ELECTROLUX DD8795-M/A

[. . . ] DD 8795 Cooker Hood Operating and Installation Instructions Contents Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 1 Recirculation Version · The air is filtered through charcoal filters and returned to the kitchen. · You will need original charcoal filters for the recirculation function. (Available from your local Service Centre). · Fix the deflector using 2 screws Ø 3. 5x9. 5 mm. 2 6 Control Panel · Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. · The hood operation can be controlled via the control ball or with the remote control (the remote control is a special accessory and is ordered separately). Every change (changing speed, switching on the lights, etc. ) is recognisable from the variation of light emitted by the control ball and by an acoustic signal. The control ball is located below on the right side of the cooker hood. The control ball is also a light signal : · No signal : The hood is switched off. · Static green light : Hood is switched on at power level 1 (minimum). · Static orange light : Hood is switched on at power level 2 (medium). · Static red light : Hood is switched on at power level 3 (maximum). · Flashing red light : Hood is switched on at intensive power level (timed at 5 minutes) · Flashing green light : Indicates the grease filter saturation - clean the grease filter · Flashing orange light : Indicates the charcoal filter saturation - clean or replace the charcoal filter. The control ball flashes orange to indicate the saturation of the charcoal filter even if the hood is used in the extraction mode and no charcoal filter is fitted. In this case, perform the signal reset operation as follows: select the intensive speed (the control ball lights up with a red flashing light), press again and hold pressed for about 3 seconds until an audible signal indicates the reset has taken place. 3 The control ball is a balancer switch. Pressing the control ball repeatedly towards the bottom, switches on the hood and you may select the motor level desired, depressing once again the hood switches off. press towards the bottom to switch on the hood. Switching on the light - Fig. 3 Press the control ball towards the top : once for submersed lighting, once again for full lighting, press again to switch off the light. Indicator light for grease or charcoal filter The air duct, in this hood, includes a device that signals when the filter requires cleaning or changing . press towards the top to switch on the lights Fig. 3 Led signal for grease filter The LED signal flickers (flickering green light) when the grease filter requires cleaning, occurs at about 40 operating hours. Ensure that the indicator light is checked each time the hood is used. Led signal for charcoal filter The LED signal flickers (flickering orange light) when the charcoal filter requires cleaning, occurs at about 160 operating hours. [. . . ] Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician. [. . . ]