User manual AEG-ELECTROLUX DD8820-AR

[. . . ] 67 Extraction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Recirculation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Control Panel - DD 8990 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68-71 Control Panel - DD 8861-8891-8821 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To interrupt the Intensive speed, press button 1 or 6. The letter P appears on the display and the remaining time (the point a is flashing), if interrupted an acoustic signal is heard. 7 - Self-Timer: times all the speed levels (the point b is flashing), and then the cooker hood switches off: The self-timer is set as follows: 1st speed level 20 minutes 2nd speed level 15 minutes 3rd speed level 10 minutes P (intensive) speed level: 5 minutes The display shows the remaining operation time, at the end of the time an acoustic signal is heard. Depressing the push-button again exits the function. Automatic Sensor calibration: The automatic calibration is carried on by the hood itself every 30 minutes. When the hood is installed for the first time or the power is cut off for many hours or days, please wait 30 minutes before the use or make a manual calibration. Manual Sensor calibration Carry out calibration with the hob off, at normal ambient room temperature and in the absence of an appreciable amount of steam: - press switch 4 for about 3secs , then press switch 1, the hood emits a sound signal to indicate calibration taking place. Sensors test When functioning in Automatic mode, the system continuously tests the efficiency of the sensors. In case of a fault the display shows 88. Contact your local Service Force Centre. In this situation the hood can, in any case, be used in the manual mode. To interrupt the Intensive speed, press button A or B. H - Light ON/OFF i A B C D E Fig. 4 Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds, then turn the hood back on again. 72 Grease and charcoal filter maintenance indicator DD 8695-8665-8625 This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter). On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Set the hood in OFF. Pressing keys B and D simultaneously for three seconds, LED F lights up and begins to flash the 1st speed led. After 1 second the 2nd speed led also flashes and the system emits a sound signal (-Beep-) to indicate setting taking place. To remove the charcoal filter signal press push buttons B and D simultaneously for 3 seconds. LED F lights up and begins to flash the 1st speed led (grease filter) and the 2nd speed led. After 1 second, only the 1st speed led continues to flash. The system emits a sound signal (-Beep-) to indicate setting taking place. [. . . ] as the engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty. Please note that proof of purchase is required for in-guarantee service calls. Help us to help you Please determine your type of enquiry before writing or telephoning. When you contact us we need to know: Your name Clear and concise details of the fault Address and post code Name and model of the appliance* Telephone number E number* Serial number* * This information can be found on the rating plate, which can be seen when the grease filters are removed. [. . . ]