User manual AEG-ELECTROLUX DD9893-M

[. . . ] La distance minimum entre la superficie de support des récipients sur le dispositif de cuisson et la partie la plus basse de la hotte de cuisine ne doit pas être inférieure à 50cm dans le cas de cuisinières électriques et de 65cm dans le cas de cuisinières à gaz ou mixtes. 1 manchon de réduction 1 déflecteur (avec rallonge) 1 clé à chenillette pour vis torx 1 support de fixation pour le groupe moteur 1 support de fixation cheminées (3 pièces à assembler) 6 vis 5 x 45 mm 6 chevilles Ø 8 mm 2 vis 2, 9 x 6, 5 8 vis 3, 5 x 6, 5 4 vis 4 x 8 2 bouchons grand modèle 2 bouchons petit modèle When used as an extractor unit, the hood must be fitted with a hose having preferably the same diameter as the outlet hole. Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/ 125 mm reduction flange provided. in this case the hood will be slightly noisier. [. . . ] At first only the grease filter LED F will light up, but when the charcoal filter LED C lights up the saturation indicator will be enabled. To disable it: Press buttons 3 and 4 again simultaneously and hold them for 3 seconds, until the charcoal filter LED goes out. LED F will start to flash when it is time to clean the grease filter. Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter. The charcoal filter LED C will start to flash when the charcoal filter needs to be replaced. This operation is necessary after approximately 160 working hours. After cleaning or replacing the filters, press button 3 for 3 seconds until the grease filter LED F or the charcoal filter LED C stops flashing. Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. DD 9893 The perimeter air suction panels are attached to the cooker hood by a series of pins and coupling springs; pull them outwards and detach them from the fastening cable. Make sure the panels are attached to the cooker hood properly (snap-fastened). DD 9863 Pull the panel (FRONT SIDE) downward with decision, unscrew safety knob and unhook it from the rear hinge. 3a Clean the perimeter air suction panels as often as the grease filters (for more information about gentle cleaning methods, read the paragraph "Cleaning" in the pages that follow). The inner crosspiece should be removed in order to access the grease filters and the inside of the cooker hood (for example: when performing maintenance work on the carbon filters). Keep the crosspiece supported during removal/fitting procedures, in order to prevent it from falling and damaging other objects. Remove it from its position using the spring release system. Re-fit the crosspieces by carrying out the above steps in reverse. Make sure the crosspiece is fixed to the cooker hood properly. The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. removing the metal grease filters · Push it towards the back of the unit and then pull it down and out. [. . . ] If you require Customer Service in the Republic of Ireland please contact us at the address below: AEG Electrolux Group (Ire) Ltd Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 (0) 1 4090751 Email: service. For general enquiries concerning your AEG appliance or for further information on AEG products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www. Uk Customer Services Department Major Appliances AEGElectrolux Addington Way Luton Bedfordshire LU4 9QQ 08705 350 350 (*) * calls to this number may be recorded for training purposes 1 reduction flange 1 deflector (with extensions) 1 Allan wrench for torx screws 1 fixing bracket for motor unit 1 support bracket for flues (3 pieces to assemble) 6 screws 5 x 45 mm 6 dowels Ø 8 mm 2 screws 2. 5 4 screws 4 x 8 2 large plug caps 2 small plug caps Safety warnings for the electrician The mains power supply must correspond to the rating indicated on the plate situated inside the hood. [. . . ]