User manual AEG-ELECTROLUX DF6260-ML

[. . . ] DF 6260 DF 6160 CHDF 6260 Dunstabzugshaube Afzuigkap Hotte Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruiksaanwijzing Notice d'utilisation et d'installation Operating and Installation Instructions Contents Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 For the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 For the installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter · The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the extraction or internal recirculation function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filter · Pull out the visor, remove the rear grease filter pulling the handle designed for this purpose, then proceed in the same way to remove the front grease filter. Hand washing · Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher · Place grease filters in dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. · Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). Fig. 2 67 Charcoal filter · The charcoal filter should only be used if you want to use the hood in the recirculation function. · To do this you will need an original charcoal filter (available from your local Service Force Centre). · Replacing the charcoal filter Type 150 Note: this filter is already installed on model DF 6260-ml9. This filter cannot be cleaned or reused. As a general rule, the activated charcoal filter should be changed once every 4 months. · Cleaning/replacing the charcoal filter Type 150 LONG LIFE Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month (when using the hood 2, 5 hours per day, on avarage). The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the charcoal, the filter should be dried in an oven for 10 minutes with a maximum temperature of 100ºC. After approximately three years of use, the charcoal filter should be replaced with a new, as the odour reduction capacity will be reduced. [. . . ] · Insert the hood in the furniture housing and engage both mounting claws (installation aids) on the right and left sides in the side wall of the wall unit and firmly hold the hood for further mounting. Then fix the hood with the 4 or 6 x Ø 4 mm screws supplied. 11 76 · If the cupboard is deeper than 300 mm, cover the gap between the hood and the wall with a finishing strip (special accessory). To install it, proceed as follows: Measure the wall distance and apply the covenng strip over the necessary width (wall distance plus 5 to 8 mm), kinking the covering strip at the appropriate notches and tearing off the surplus material (removing the protective foil). [. . . ]