User manual AEG-ELECTROLUX DF6260-ML/GB

[. . . ] CHDF 6260 DF 6260 Dunstabzugshaube Afzuigkap Hotte aspirante Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruiksaanwijzing Manuel de montage et d'utilisation Operating and Installation Instructions Contents Safety warnings for user for kitchen unit installer Introduction Extractor version Filter Version Description of the appliance Hood Operation Maintenance and care Metal grease filter Open the metal grease filter Carbon filter Changing the light bulb(s) Cleaning Special accessories Technical assistance service Guarantee conditions Technic Details Mounting accessories included Electrical connection Safety warnings for the electrician Installation 69 69 69 71 71 71 71 72 73 73 73 74 75 76 76 76 77 79 79 80 80 81 68 Safety warnings for user · Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. · Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control. · The hot oil in the frying pan might ignite due to overheating. [. . . ] Insert the carbon filter into the lugs of the holding frame above using the 2 red clips to retain it below, press the red clips inwards, and insert the carbon filter in the holding frame. Press both red lugs upwards (towards the inside of the housing) and remove the carbon filter downwards. Clean the internal housing only with warm washing-up liquid' suds (never use any abrasive cleaners, brushes, or scouring agents). · Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. · The activated carbon filter can be ordered from the AEG technical assistance service. Fig. 3 74 Warning · Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. · The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb(s) · Disconnect the unit from the mains power supply. · Unlock the lighting cover (D) by twisting the bolts to the left and fold down the bulb cover. Replace the old light bulb(s) with a new light bulb of the same kind. · Close the bulb cover and relock it by twisting the bolts to the right. · If the light does not come on, make sure the bulb has been screwed in correctly before contacting the technical assistance service. Fig. 4 D 75 Cleaning · Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor's protective grid. · Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. · Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. · It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Special accessories Carbon filter KLF 60/80 Front panel BL3D-w (White) Front panel BL3D-b (Black) Front panel BL3D-m (Inox) Finishing strip Clips (3x) E-Nr. 610 899 421 942 118 603 942 118 604 942 118 605 660 012 698 660 012 697 Technical assistance service You are welcome to telephone our technical assistance service (see list of technical assistance centres) whenever you need information or in the unlikely event of a fault. When calling, please be ready to specify: 1. [. . . ] · Important: Detach and insert the grease filters only when the vapour catcher is fully withdrawn. First remove the rear and then the front grease filter. · For 19 mm side walls, the spacer discs clipped in on the appliance body must be taken out. Mount the hood with 4 or 6 x Ø 4 mm screws. [. . . ]