User manual AEG-ELECTROLUX DI8821-M-A

[. . . ] DI 8821 Cooker Hood Operating and Installation Instructions Contents Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press again for more than 1 1/2 seconds to reset the cooker hood to "stand by". 2 - Light ON/OFF 3 - Display 4 - Start and choice of motor speed 1-2-3-1-2. . . . . . . . . The Intensive speed runs for 5 minutes: If the hood is on when the Intensive speed is activated, the hood will revert to previous speed after 5 minutes. If the hood is off when the Intensive speed is activated, the hood will automatically turn off after 5 minutes. To interrupt the Intensive speed, press button 1 or 5. The letter P appears on the display and the remaining time (the point "a" is flashing), if interrupted an acoustic signal is heard. 6 - Self-Timer: times all the speed levels (the point "b" is flashing), and then the cooker hood switches off: The self-timer is set as follows: 1st speed level 20 minutes 2nd speed level 15 minutes 3rd speed level 10 minutes The display shows the remaining operation time, at the end of the time an acoustic signal is heard. Depressing the push-button again exits the function. Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds. After reconnecting the power supply wait 15 seconds and then check that the cooker hood is now operating correctly. 7 Grease and charcoal filter maintenance indicator This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter). On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Press buttons 4 and 5 simultaneously and hold them for 3 seconds. At first only the grease filter LED F will light up, but when the charcoal filter LED C lights up the saturation indicator will be enabled. To disable it: Press buttons 4 and 5 again simultaneously and hold them for 3 seconds, until the charcoal filter LED C goes out. Grease filter LED (F) LED F will start to flash when it is time to clean the grease filter. Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (C) The charcoal filter LED C will start to flash when the charcoal filter needs to be replaced. This operation is necessary after approximately 160 working hours. Resetting the saturation indicator After cleaning or replacing the filters, press button 1 for 3 seconds until the grease filter LED F or the charcoal filter LED C stops flashing. 8 Maintenance and Care · The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood · Clean the outside of the hood using a damp cloth and a mild detergent. · Never use corrosive, abrasive or flammable cleaning products. · Never insert pointed objects in the motor's protective grid. · Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. [. . . ] The side of the support with connection box corresponds to the side of the control panel with hood assembled. · Insert and tighten another 2 screws in the remaining free holes (8) for secure fixing. · Carry out the electrical connection (9) to the mains power supply, only turn on the power supply upon completion of assembly. · Hook the hood onto the support (10) , ensuring it fits properly ­ to hook the hood onto the support partially tighten 4 screws (see also step 12). [. . . ]