User manual AEG-ELECTROLUX DI9814-M

[. . . ] DI 9814 User manual Cooker Hood Contents Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Extraction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Recirculation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The letter P appears on the display and the remaining time (the point "a" is flashing), if interrupted an acoustic signal is heard. 6 - Self-Timer: times all the speed levels (the point "b" is flashing), and then the cooker hood switches off: The self-timer is set as follows: 1st speed level 20 minutes 2nd speed level 15 minutes 3rd speed level 10 minutes The display shows the remaining operation time, at the end of the time an acoustic signal is heard. Depressing the push-button again exits the function. Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds. After reconnecting the power supply wait 15 seconds and then check that the cooker hood is now operating correctly. Grease and charcoal filter maintenance indicator This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter). On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Press buttons 4 and 5 simultaneously and hold them for 3 seconds. At first only the grease filter LED F will light up, but when the charcoal filter LED C lights up the saturation indicator will be enabled. To disable it: Press buttons 4 and 5 again simultaneously and hold them for 3 seconds, until the charcoal filter LED C goes out. Grease filter LED (F) LED F will start to flash when it is time to clean the grease filter. Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (C) The charcoal filter LED C will start to flash when the charcoal filter needs to be replaced. This operation is necessary after approximately 160 working hours. Resetting the saturation indicator After cleaning or replacing the filters, press button 1 for 3 seconds until the grease filter LED F or the charcoal filter LED C stops flashing. The resetting of the saturation indicator MUST be done in stand-by, never disconnect the hood from the mains. Correct ventilation If the cooker hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open. 7 Maintenance and Care Warning!Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Metal grease filter · The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filters · Pull the handle downwards, then remove the filter. [. . . ] · Drill as shown (6 holes for 6 wall plugs ­ 4 plugs for fixture), screw the outer screws leaving a space of about 1 cm. between the screw head and the ceiling (4). · Fit an exhaust pipe inside the support (5) and connect it to the motor compartment connection ring (exhaust pipe and fixing brackets are not supplied). · Hook the frame onto the 4 screws (6 - see also step 4). [. . . ]