User manual AEG-ELECTROLUX DM8600-M-A

[. . . ] DM 8600 Cooker Hood Operating and Installation Instructions Contents Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You will need original charcoal filters for the recirculation function. (Available from your local Service Centre) 6 Control Panel · Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. The control switches are located on the hood's front panel: A - Mains switch, OFF. B - Start and choice of motor speed 1-2-3 C - Indicates speed 1 (LED). D - Indicates speed 2 and saturation of the grease filter (LED) E - Indicates speed 3 and saturation of the charcoal filter (LED) (flashing LED) F - Indicates Intensive speed (LED). The Intensive speed runs for 5 minutes: If the hood is on when the Intensive speed is activated, the hood reverts to previous speed after 5 minutes. If the hood is off when the Intensive speed is activated, the hood will be turned off after 5 minutes. To interrupt the Intensive speed, press button A or B. 2 B CDE F G H I Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds, then turn the hood back on again. 7 Grease and charcoal filter maintenance indicator This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter). On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Set the hood in "OFF". Press buttons B and G simultaneously and hold them for 3 seconds. At first only the grease filter LED D will light up, but when the charcoal filter LED E lights up the saturation indicator will be enabled. To disable it: Press buttons B and G again simultaneously and hold them for 3 seconds, until the charcoal filter LED E goes out. Grease filter LED (D) LED D will start to flash when it is time to clean the grease filter. Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (E) The charcoal filter LED E will start to flash when the charcoal filter needs to be replaced. This operation is necessary after approximately 160 working hours. Resetting the saturation indicator After cleaning or replacing the filters, press button A for 3 seconds until the grease filter LED D or the charcoal filter LED E stops flashing. the grease filter LED D or the charcoal filter LED E stops flashing. 8 Maintenance and Care · The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood · Clean the outside of the hood using a damp cloth and a mild detergent. [. . . ] When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician. 13 Wall unit mounting - Fig. 6-7 First decide which functioning mode is better for you. If you decide to use the hood in extraction mode we suggest you position the upper section of the chimney so that the oulet slots are not visible once installation is completed, however if is decided to use the hood in rrecirculation mode BE SURE that the side with slots is up (see also A-B-C sequence on on Fig. [. . . ]