User manual AEG-ELECTROLUX E36DF76PSS INSTALL

[. . . ] Installation Instructions Dual Fuel Ranges E30DF74EPS E36DF76EPS E48DF76EPS 5995447082 2 Safety IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Warning or Caution based on the risk type. Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CA UTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. CAUTION CA UTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. IMPORT IMPOR TANT Indicates installation, operation or maintenance information which is important but not hazard related. Safety SAFETY PRECAUTIONS WARNING · · Read all instructions before using the appliance. [. . . ] Peel off the protective layer of plastic that covers the door panel. Installation MAKING THE ELECTRICAL CONNECTION WARNING · Models E30DF74EPS, E36DF76EPS and E48DF76EPS must be connected to a grounded, metallic, permanent wiring system. Alternatively, a grounding conductor should be connected to the grounding terminal or lead on the appliance. Failure to do so may result in an electric shock hazard. Do not use an extension cord with this appliance. Such use may result in fire, electrical shock, or other personal injury. Do not install a fuse in the neutral or ground circuit. A fuse in the neutral or ground circuit may result in an electrical shock hazard. 19 · · Grounding Instructions This appliance must be electrically grounded. With the range positioned directly in front of the cabinet cutout, feed the appliance conduit to the electrical junction box. Then, depending upon local codes, utilize one of the following techniques to connect the appliance to the electrical power supply: Connecting to a Four-Wire Electrical System 1. Separate the green and white appliance wires. Connect the white appliance wire to the neutral (white) supply wire in the junction Figure 14 box. Connect the black appliance wire to the black (L1) power supply wire in the junction box. Connect the red appliance wire to the red (L2) power supply wire in the junction box. Connect the green appliance wire to the green house grounding wire in the junction box. Cable from power supply Junction box RED RED GREEN GREEN WHITE WHITE BLACK BLACK Wire nut (4 places) Conduit from appliance Connecting the appliance to a four-wire power supply 20 Installation WARNING Do not connect the green appliance wire to the neutral (white) supply wire unless local building codes permit. Connecting the Green Appliance Wire to the Neutral (White) Supply Wire ­ Where Local Codes Permit 1 2 3 Connect the green and white appliance wires to the neutral (white) supply wire in the junction box. Connect the black appliance wire to the black (L1) power supply wire in the junction box. Connect the red appliance wire to the red (L2) power supply wire in the junction box. Figure 15 Cable from power supply Junction box RED RED GREEN WHITE WHITE BLACK BLACK Wire nut (3 places) Conduit from appliance Connecting the appliance to a three-wire power supply Installation 21 Connecting the Green Appliance Wire to a Grounded Supply Wire or a Grounded Cold Water Pipe ­ Where Local Codes Permit. 1 2 3 4 5 6 Separate the green and white appliance wires. Connect the white appliance wire to the neutral (white) supply wire in the junction box. Connect the black appliance wire to the black (L1) power supply wire in the junction box. Connect the red appliance wire to the red (L2) power supply wire in the junction box. Connect the green appliance wire to a grounded supply wire in the junction box or to a grounded cold water pipe. If connecting to a grounded cold water pipe, a separate copper grounding wire (No. 10 minimum) must be connected to a grounded cold water pipe by means of a clamp and then to an external grounding connector screw. WARNING · · · Do not ground the appliance to a gas supply pipe or hot water pipe. [. . . ] 9-3 Reinstall the burner base (see Figure 9-1). 9-4 Measure the gap between the end of the shutter connector and the opposite end of the shutter opening with the pocket rule (see Figure 9-2). 9-5 Compare the measured gap to the gap listed in Table 9-2 for the appropriate model number and the burner location. Page 8 Professional Series Range LPG Conversion Kit Burner E30DF74EPS E36DF76EPS E48DF76EPS Location (30-Inch) (36-Inch) (48-Inch) Left Rear HN A-0053-E HN A-0053-E HN A-0053-E Left Front HN A-0052-E HN A-0052-E HN A-0052-E Right Rear HN A-0053-E HN A-0052-E HN A-0052-E Right Front HN A-0053-E HN A-0053-E HN A-0053-E Center Rear HN A-0053-E HN A-0053-E Center Front HN A-0053-E HN A-0053-E Table 9-1 Air Shutter Part Numbers Burner E30DF74EPS E36DF76EPS E48DF76EPS Location (30-Inch) (36-Inch) (48-Inch) Left Rear . 36/9. 2 . 38/9. 7 . 39/9. 8 Left Front . 34/8. 6 . 27/6. 9 . 12/3. 1 Right Rear . 35/8. 9 . 29/7. 4 . 18/4. 7 Right Front . 37/9. 4 . 39/9. 9 . 38/9. 6 Center Rear . 40/10. 0 . 38/9. 7 Center Front . 39/9. 8 . 40/10. 1 Table 9-2 Air Shutter Gaps Settings (in/mm) Burner Base Air Shutter Shutter Connector Compression Nut Figure 9-1 Air Shutter Assembly Shutter Gap Apply thread-locker here End of shutter connector Figure 9-2 Air Shutter Reassembly and Gap Adjustment Page 9 STEP 10 Perform Leak Tests 10-1 Make sure that all knobs on the front of the range are in the off position. 10-2 With electrical power to the range disconnected, open the LPG supply valve. [. . . ]