User manual AEG-ELECTROLUX EA0302FL

[. . . ] For the safety of hotel guests and personnel, it has been established by inspectors that the coolant poses no threat to health. Coolants 3. 0 WARRANTY AND CUSTOMER SERVICE Warranty arrangements are in accordance with EC Directive 44/1999/CE and the normal conditions applicable for the country concerned. For warranty or service, please contact our customer services section. Spares can be obtained all over Europe from our relevant customer service points. When contacting customer service, please always state model, product and serial number! [. . . ] Ventilation must be provided as shown in alternatives A, B, C or D 4. The ventilation duct must at least measure 105mm x the wtdth of the refrigerator 5. Only the entire cooling unit must project into the duct as shown 6 Air passing through the duct must not be preheated by any source of heat 7. Ventilation grills, if used, must have openings of at least 200cm² each Where a socket outlet is used for the mains connection lead, the outlet must be freely accessible. 5 4. 6 Securing EA 330 The miniCool must be screwed onto the cupboard using the lower hinges. 1. Put on cap. 4. 7 Connecting the Device to the Electricity Supply The device must be connected to a properly earthed socket in line with the relevant valid country regulations. Check prior to initial operation that the voltage noted on the model label corresponds to the mains voltage. If this is not the case, do not connect the device and contact your dealer! If the connection cable is damaged it must be replaced by the Customer Service at Dometic, or by respectively qualified personnel, in order to prevent any hazards. Plug connection (for United Kingdom only) If a 3-pin 13 amp fused plug is used, it should be fitted with a 3 amp fuse; with other plug types, the circuit should contain a 5 amp fuse. This appliance conforms with the requirements of EEC directive No. 82/449 relating to radio interference. Attention: For GB Only ! Warning - This appliance must be earthed. IMPORTANT The wires in the mains lead of this appliance are coloured in accordance with the following code: GREEN and YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. Connect the GREEN and YELLOW coloured wire to the plug terminal marked letter E or earth symbol or coloured green or green and yellow. Connect the BROWN coloured wire to the plug terminal marked letter L or coloured red. Accordingly, this is registered and processed at the hotel reception. The miniCool wiring connection is situated at the rear of the appliance and consists of a 3-pin terminal strip (1). 1= terminal strip 2= approximation switch A= blue (opening mechanism) B= black (closing mechanism) C= white FIG. 1 10 5. 6 Interior Light (LED) via a sensor. Changing : When the door is opened, the lighting in the cooling shelf is switched on 1. Clip reflector disk back in. To obtain spare bulbs, please contact your Dometic Service Centre. 11 5. 7 miniCools manufactured by Dometic GmbH are free from CFC/HCFC and fluorinated hydrocarbons. The cooling unit uses ammonia as the coolant (a natural compound of hydrogen and nitrogen). Cyclopentane, which does not damage the ozone layer, is used as propellant for the insulation made from PU-foam. Environmental Advice 5. 8 In order to ensure the re-use of recyclable packaging materials, these must be disposed of using local collection systems. The device itself must be handed over to a disposal company or local council which will guarantee the correct use of recyclable materials and the proper disposal of the rest. Disposal 5. 9 Energy Saving Tips At an average room temperature of approx. 22°C, it is sufficient to operate the miniCool with an average thermostat setting. If possible, always store pre-cooled goods. Do not expose the miniCool to direct sunlight and do not place it close to a source of heat. [. . . ] Possible Cause a. ) The cooling aggregate is not sufficiently ventilated. Self Help a. ) Check that the ventilation grids are not covered. Check that device has been installed properly (installation instruction 4. 5). b. ) Follow installation instruction 4. 5. [. . . ]