User manual AEG-ELECTROLUX EA0600C

[. . . ] Parts which heat up should not be exposed. Wherever possible the back of the product should be close to a wall but leaving the required distance for ventilation as stated in the installation instructions. Before defrosting, cleaning or maintenance work is carried out, be sure to switch off the appliance and unplug it. DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. [. . . ] Ventilation grills, if used, must have openings of at least 200cm2 each During installation, please ensure the mains plug is accessible at all times. 4. Positioning the appliance When first using this refrigerator please consider the following points: ENSURE REFRIGERATOR IS LEVEL THE PIPEWORK AT THE BACK GETS HOT IN USE THE REFRIGERATOR HAS NO 'MOTOR' AND IS THEREFORE VIRTUALLY SILENT ALLOW AT LEAST 3 HRS. FOR SIGNS OF COOLING During the refrigeration process, the appliance gives off heat from the condenser (under the upper part of the rear cover) into the surrounding air. The more ventilated the condenser is, the more effective the refrigeration will be. The other condition for satisfactory operation is that the appliance stands on a flat surface. This is best seen by placing a glass of water on top of the appliance. It is important that the appliance is not directly exposed to radiated heat (sunlight, radiator, near an oven, etc. ). Figure 2. 4. 1. Installation instructions The refrigerator is equipped with an electrically heated absorption cooling unit which is virtually silent in operation. The fridge is designed for free-standing installation, but can be built-in if the following conditions are complied with to ensure satisfactory operation and maximum cooling efficiency. IMPORTANT Please follow the installation details below carefully Guarantee is valid for products installed as described only. The refrigerator must be level both directions 2. It is advisable to leave some space between the products in the cabinet to ensure efficient and even cooling. If the shelves are packed too tightly there may be unacceptable temperature variations. If the lightbulb needs changing, pull out the plug and proceed as follows: Press the metal reflector to one side and draw the lamp covering backwards. Replace the bulb and push the covering back into place. A new 10-watt bulb can be obtained at any service shop. 7. Useful suggestion Lay the appliance on its back. Remove the door, together with the two hinges (2), from the housing. Remove the two cover caps (3) from the housing and place them in the open hinge holes in the housing. Place the bottom righthand hinge in the top left of the door and the top righthand hinge in the bottom left of the door and hang the door on its hinges in the open cover cap holes in the housing. Secure the hinges and cover caps with the 8 screws. Check that the door closes easily and is sealed properly. 10. 6) Frost will gradually form on the cooling surfaces and it must not be allowed to become too thick since it acts as an insulator and interferes with the cooling. [. . . ] In the event of a fault developing, contact your nearest Service Centre-see local telephone directory. 15. Putting into operation Technical data: Model Type Gross volume Mains operation Input Energy consumption Climate class Refrigerant EA 3100 EA 0300, EA 0301 EA 0302, MF20-60 31 litre 220 - 240V (AC) 90W 0. 97 kWh/24h N 245g NH3 +H2O EA 3080 RA 80 MF20-60 23 litre 220 - 240V (AC) 90W 0, 92 kWh/24h N 245g NH3 +H2O EA 3120 MF20-60 31 litre 220 - 240V (AC) 90W 0. 99 kWh/24h N 245g NH3 +H2O EA 3140 RA 140 RA 0450 MF20-60 41 litre 220 - 240V (AC) 90W 1. 07 kWh/24h N 245g NH3 +H2O 15. 1 Connecting to electrical mains The appliance may only be operated from nominal voltage mains as shown on the data plate. The appliance mains plug may be connected to a mains socket earthed in accordance with regulations. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. [. . . ]