User manual AEG-ELECTROLUX EA3255EBP

[. . . ] Visit our website for: Get usage advice, brochures, trouble shooter, service information: www. aeg. com Register your product for better service: www. aeg. com/productregistration Buy Accessories, Consumables and Original spare parts for your appliance: www. aeg. com/shop CUSTOMER CARE AND SERVICE We recommend the use of original spare parts. When contacting Service, ensure that you have the following data available. The information can be found on the rating plate. Warning / Caution-Safety information General information and tips Environmental information Subject to change without notice. ENGLISH 3 1. SAFETY INSTRUCTIONS Before the installation and use of the appliance, carefully read the supplied instructions. [. . . ] Processing residues can stay in the appliance. Do not use detergent and do not load the baskets. If you use the combi detergent tablets, activate the multitab option. ENGLISH 9 6. 1 Adjusting the water softener Water hardness German degrees (°dH) 51 - 70 43 - 50 37 - 42 29 - 36 23 - 28 19 - 22 15 - 18 11 - 14 4 - 10 <4 French degrees (°fH) 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 33 - 39 26 - 32 19 - 25 7 - 18 <7 mmol/l Clarke degrees 64 - 88 53 - 63 46 - 52 36 - 45 28 - 35 23 - 27 18 - 22 13 - 17 5 - 12 <5 Water softener adjustment Manual Electronic 10 9 8 7 6 51) 4 3 2 12) 9. 1 - 12. 5 7. 6 - 9. 0 6. 5 - 7. 5 5. 1 - 6. 4 4. 0 - 5. 0 3. 3 - 3. 9 2. 6 - 3. 2 1. 9 - 2. 5 0. 7 - 1. 8 < 0. 7 2 1) 2 1) 21) 21) 21) 21) 1 1 1 12) 1) Factory position. 2) Do not use salt at this level. You must adjust the water softener manually and electronically. Manual adjustment Turn the water hardness dial to the position 1 or 2. Electronic adjustment 1. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. Press and hold Delay and Start at the same time until the indicators (A), (B) and (C) flash. 4. • The indicators (B) and (C) go off. • The indicator (A) continues to flash. • The display shows the setting of = the water softener. Make sure that the release button locks into position. • Only the indicator of the phase in operation stays on. • Let the dishes become cold before you remove them from the appliance. • First remove the items from the lower basket, then from the upper basket. • There can be water on the sides and on the door of the appliance. Stainless steel becomes cool more quickly than the dishes. Cancelling the programme Press and hold Delay and Start at the same time until: • All the programme indicators come on. • The display shows 2 horizontal status bars. Make sure that there is detergent in the detergent dispenser before you start a new programme. At the end of the programme When the programme is completed, the end indicator comes on and the display shows 0. 8. HINTS AND TIPS 8. 1 The water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The water softener neutralises these minerals. The dishwasher salt keeps the water softener clean and in good conditions. [. . . ] • The quantity of detergent is too much. Stains and dry water drops on glasses and dishes • The released quantity of rinse aid is not sufficient. Adjust the rinse aid selector to a higher position. • The quality of the detergent can be the cause. Dishes are wet • The programme is without a drying phase or with a low temperature drying phase. [. . . ]