User manual AEG-ELECTROLUX EFC009.1X-CH

[. . . ] Gebrauchsanweisung , Manuel d'utilisation EFC 009. 1X Istruzioni per l'uso , User manual D F I UK Contents Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 For kitchen unit installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mounting of grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For the best performance, we recommend using the low speeds in normal conditions and the high speeds in particular cases of strong odour and vapour concentration. We recommend starting up the hood a few minutes before cooking and keeping it running until all the odours have been eliminated. Control devices for the grease filter and carbon filter This hood has a device which warns you when to clean the grease filter or replace the carbon filter (in the case of the air recircultion version). This hood is delivered without a carbon filter. For this reason the warning signal to replace the carbon filter is not connected. If the hood will be used for recirculation of air, with carbon filter, the warning signal have to be connected as follows: Press the buttons B and G at the same time for about 3 seconds. When the LED marked C lights up, the warning signal is connected. To disconnect the warning signal, press the buttons B and G at the same time for about 3 seconds until the LED marked C goes out. 5 MIN 0 123 FC 0 I A B EFCD G H I A ­ Motor OFF button B ­ ON button and motor speed selection button 1 - 2 - 3 - 1 - 2 - . E ­ Speed 1 LED F ­ Speed 2 LED and grease filter saturation LED (flashes) C ­ Speed 3 LED and carbon filter saturation LED (flashes) D ­ Intensive speed indicator LED G ­ Intensive speed ON switch This speed should be used when the concentration of cooking fumes or odours is particularly strong (for example when frying, cooking fish etc. ). The fast speed will run for about 5 minutes and then return to the speed previously set automatically (1, 2 or 3), or switch off if no speed was selected. To turn off the fast speed, before the end of the 5 minutes, press button A or button B. H ­ OFF lamp button I ­ ON lamp button If the hood fails to operate correctly, briefly disconnect it from the mains power supply for almost 5 sec. Then plug it in again and try once more before contacting the Technical Assistance Service. Grease filter saturation led The LED marked F warns you when the grease filter needs to be cleaned. This LED flashes to warn you that the grease filters must be cleaned. Generally, these must be cleaned after 40 hours of use. Read the maintenance instructions provided for the grease filters. Carbon filter saturation led The LED marked C indicates carbon filter needs to be replaced. This must be done after approximately 160 hours of use. Read the instructions provided for replacing the carbon filter. To restore the LED for the filter warnings. After cleaning of the grease filter and exchange of the carbon filter, press button A for about 3 seconds until the LED F stops flashing. Correct ventilation To have the cooker hood working correctly the windows in the kitchen should be closed. In stead a window in an adjacent room should be open. 35 Maintenance The hood must always be disconnected from the mains power supply before beginning any maintenance work. Cleaning · Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor's protective grid. · Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. · Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. [. . . ] · Fix the upper part of the chimney to the supporting structure with two screws "b" 2, 9x6, 5 (Fig. 11 · Fit four auto locking nuts on the four pins located on the upper side of the hood (Fig. 12 40 · Fit the glass part on top of the hood · Fit temporarily the hood on the supporting structure by means of the already mentioned pins with nuts to be inserted on the proper holes located on the lower side of the supporting structure. Rotate the hood until it stops (a - Fig. [. . . ]