User manual AEG-ELECTROLUX EFC009X-CH

[. . . ] Gebrauchsanweisung, Manuel d'utilisation, Istruzioni per l'uso EFC 009 X Gebruiksaanwijzing, User Manual D F I NL UK Contents Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Mounting of grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Disconnect the power plug and cut the power cord at hood inlet. Check with the authorities for information of how to proceed for disposal. Description of the appliance 1. Grease filters Standard accessories included: q Screws for mounting q No return valve (mounted on air outlet) q Drilling scheme q Connection ring q Deflector (Recycling version) 1 2 3 Mounting of grease filters The grease filters are supplied apart inside an apposite package; follow these instructions for mounting: q Fit the hooks at the centre of the hood and push the handle upwards until the filter locks. Dismount the filter the opposite way q Pull the handle downwards to loosen the filter. 1). Function The hood may be used as follows: - Exhausting version - Recycling version Fig. 1 A - Ø 150 mm Exhausting version The air is vented outdoors by a 150 mm duct which must be connected to connecting ring with no return valve A on top of the motor package (Fig. 2 The hood cannot be connected to flues of other appliances that run on energy sources other than electricity. Please, keep to the provisions of official directives regarding the question of fumes discharge. Recycling version The air is filtered through a carbon filter and recirculated into the room through the top sides of the chimney (Fig. This version is used when there is no exhaust duct for venting outdoors or when it is impossible to install one. 3 Special accessories Active carbon filter When the hood is used in recirculation mode an active carbon filter should be used. Order by the retailer PNC 942 120 182 Installation Unpacking Check that the cooker hood has no damages. Transportation damages should immediately be reported to the one responsible for the transport Damages, faults and eventually missing details should immediately be reported to the seller. Take care of the packing material so that small children cannot play with it. Placement The hood is to be mounted hanging from the roof. When installed, the hood must be not less than 65 cm. 4 Min 65 cm Min 75 cm Electrical connection The hood has a power cord with moulded plug with earth connection to be connected to a wall outlet of 230 V. The power outlet should be pre-mounted in such a way that the power cord is invisible when the hood is fully mounted. The power cord length is 1, 25 m. As it is then hard to disconnect the power plug for cleaning and service, an easy accessible two pole switch should be fitted. The switch should conform to regulations with an opening distance between contacts of not less than 3 mm. 49 Mounting of hood First set the telescopic support structure on the right direction and drill as indicated on the drilling scheme supplied with the hood. q The two sections of the structure are fixed one each other with 8 screws (fig. Remove all screws, regulate the lenght of the structure according the exigencies, fit again the 8 screws. [. . . ] Read the instructions provided for replacing the carbon filter. Once you have replaced the carbon filter, press button A and button B together for about two seconds until you hear the acoustic signal (beep). The carbon filter saturation led C will now stop flashing. N. B. : the carbon filter saturation led will also flash even if the hood is used in the exhausting version (i. e. [. . . ]