User manual AEG-ELECTROLUX EFC60670X

[. . . ] 14 Something Not Working . . . . . . . . . . . . . . . . . . 14 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. Environmental information. electrolux safety warnings 5 GB Safety warnings For the user · The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. [. . . ] - the length should be no more than: 3 metres with one 90° bend 2 metres with two 90° bends Bends of more than 90° will reduce the efficiency of the hood and reduce the airflow. · Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood. electrolux description of the appliance 7 Description of the Appliance · The cooker hood is designed to from extract unpleasant odours from the kitchen, it will not extract steam. · The hood is supplied as an extractor unit and can also be used with a recirculation mode by fitting a charcoal filter. Extraction mode · In this mode fumes are extracted to the outside via a hose connected to the coupling ring ring. · In order to obtain the best performance the hose should have a diameter equal to the outlet hole. Coupling ring GB Recirculation Recirculation mode · The air is filtered through a charcoal charcoal filter and returned to the kitchen. · You will need an original charcoal filter for the recirculation mode. (See Special Accessories). 8 electrolux electrolux control panel Control Panel GB · Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. · Correct ventilation: If the cooker Correct hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open. · The control switches are located on the hood's front panel electrolux control panel 9 GB Light switch (ON/OFF) Push-button 1 (ON/OFF) Push-button 3 (ON/OFF) ON/OFF motor speed key Push-button 2 (ON/OFF) · Light switch (ON/OFF): this switch is used to turn the light fitted in the hood on and off. · ON/OFF motor speed key: serves to enable and disenable the speed selection keys. · Push-button 1 (ON/OFF): used to set the fan to speed 1. · Push-button 2 (ON/OFF): used to set the fan to speed 2. · Push-button 3 (ON/OFF): used to set the fan to speed 3. 10 electrolux electrolux maintenance and care Maintenance and Care GB Before from · Before performing any maintenance operation, isolate the hood from the off removing electrical supply by switching off at the connector and removing the connector fuse. through Or if the appliance has been connected through a plug and socket, then the removed from plug must be removed from the socket. grease Metal grease filter · The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. grease Removing the metal grease filter · Use the spring handle and remove the filter downward. Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. [. . . ] · Mark the wall with a centre line, this will aid mounting procedure (1) position the (1), template so that the mid line printed on the template matches with the centre line previously drawn, the lower side of the template corresponds to the lower side of the hood once mounted (2) (2). · Drill two holes Ø 8mm and fix the support bracket with two wall plugs and screws (3) Hang the hood (4) and adjust its position (5-6) (3). · From the inside of the hood mark two points for fixing (7) (7). · Remove the hood (8) and drill two holes Ø 8mm (9) fit two wall plugs (10) (9), (10). [. . . ]