User manual AEG-ELECTROLUX EFC6940/CH

[. . . ] Gebrauchsanweisung , Notice d'utilisation et d'installation, Istruzioni per l'uso, User manual EFC 6940 - EFC 6941 EFC 1410 Installatie- en gebruiksaanwijzing, Instrucciones de montaje y manejo, Manual de Instruções EFC 69406941 EFC 1410 SM 8090 SM 8060 SM 8091 SM 8092 SM 8062 SM 8093 D F I UK NL E P Contents UK Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 for the installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 for the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher machine Place grease filters in dish washer. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discoloration of the filter can occur, this does not have any impact on its performance. Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). Fig. 5 40 Charcoal filter The charcoal filter should only be used if you want to use the hood in its filtering function. To do this you will need an original ELECTROLUX charcoal filter (see special accessories). Cleaning/replacing the carbon filter Unlike other carbon filters, the LONGLIFE charcoal filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month. The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the charcoal, the filter should be dried in an oven for 10 minutes with a temperature of maximum 100º C. After approximately three years of use, the carbon filter should be replaced with a new, as the odour reduction capacity will be reduced. Mounting Remove the frame i which supports the filter h by turning 90° the two knobs g, Fig. Insert the coal mattress inside the frame and put all parts back in their place. Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. The charcoal filter can be ordered from the ELECTROLUX technical assistance service. g g h g i g Fig. 6 Changing the light bulb Disconnect the cooker hood from the main supply. [. . . ] Assembling the deflector (3 parts only for filter version): The three parts should be fixed with 2 screws, the deflector extension is adjustable and should correspond to the width of the chimney flue support, to which it is then fixed. Model EFC 6940-6941 only The vapour screen is not supplied and must be purchased, see the cover and page 83 and choose the preferred one. 11: Assemble the frame to the motor group (a). Connect lamps and control panel to the motor housing (b). [. . . ]