User manual AEG-ELECTROLUX EFC934X

[. . . ] Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified time period. [. . . ] Q. ty 1 1 2 2. 1 2. 2 9 14. 1 15 1 1 1 1 2 1 Product Components Hood Body, complete with: Controls, Light, Blower, Filters Telescopic Chimney comprising: Upper Section Lower Section Reducer Flange 150-120 mm Air Outlet Connection Extension Air Outlet Connection Installation Components Hood Body Fixing Bracket Upper Chimney Section Fixing Brackets Wall Plugs Screws 4, 2 x 44, 4 Screws 2, 9 x 9, 5 Documentation Instruction Manual 1 15 14. 1 9 12c 12a 7. 2. 1 11 Ref. Q. ty 7. 1 1 7. 2. 1 2 11 6 12a 6 12c 6 Q. ty 1 7. 1 12c EN 7 7 INSTALLATION Wall drilling and bracket fixing 12 7. 1 287 650 min. Wall marking: Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. Draw a horizontal line at 650 mm above the hob for installation without the back panel, or at height H (H = height of the visible part of the panel) for installation with the back panel. Place bracket 7. 1 on the wall as shown, 287 mm above the horizontal reference line, aligning the centre (notch) with the vertical reference line. Mark the wall at the centres of the holes in the bracket. Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. Mark the wall at the centres of the holes in the bracket. Place bracket 7. 2. 1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. Mark the wall at the centres of the holes in the bracket. REAR PANEL (OPTIONAL) The Rear Panel must be fitted before fixing the hood body and, for both upper an lower positiion fixing, must be fitted at the correct height prior to installing the bases. Lower exhaust flue Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated. Fix the lower part laterally to the hood body using the 2 screws 12c (2, 9 x 9, 5) supplied. 7. 2. 1 12c 1 12c EN 1 10 0 USE 3 12 01 01 V L M L M V Light Motor Speed Switches the lighting system on and off Switches the extractor motor on and off Sets the operating speed of the extractor: 1. Low speed, used for a continuous and silent air change in the presence of light cooking vapour. Medium speed, suitable for most operating conditions given the optimum treated air flow/noise level ratio. Maximum speed, used for eliminating the highest cooking vapour emission, including long periods. EN 1 11 1 MAINTENANCE Grease filters CLEANING METAL SELF- SUPPORTING GREASE FILTERS The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. Wash the filters, taking care not to bend them. When refitting the filters, make sure that the handle is visible on the outside. Activated charcoal filter (Recirculation version) These filters are not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently with heavy usage. REPLACING THE ACTIVATED CHARCOAL FILTER Remove the metal grease filters Remove the saturated activated charcoal filter as shown (A). Replace the metal grease filters. B A Lighting LIGHT REPLACEMENT 40 W incandescent light. [. . . ] Replace the metal grease filters. B A Lighting LIGHT REPLACEMENT 40 W incandescent light. Unscrew the bulbs and replace them with new ones having the same characteristics. Replace the metal grease filters. EN 1 12 2 The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. [. . . ]