User manual AEG-ELECTROLUX EFC938X/2

[. . . ] 45 For both versions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Mounting of carbon filter (for recirculating version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Using the hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Intensive speed button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Control devices for the grease filter and carbon filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Cooker hood is ready to be used for air recycling (carbon filter already mounted in place). Exhausting version The air is vented outdoors by a 150 mm duct which must be connected to connecting ring with no return valve on top of the motor package. The hood cannot be connected to flues of other appliances that run on energy sources other than electricity. Please, keep to the provisions of official directives regarding the question of fumes discharge. Recycling version The air is filtered through a carbon filter and recirculated into the room through the top sides of the chimney (Fig. This version is used when there is no exhaust duct for venting outdoors or when it is impossible to install one. 2 Special accessories Active carbon filter When the hood is used in recirculation mode an active carbon filter should be used. Order by the retailer: PNC 942 120 182 Installation Unpacking Check that the cooker hood has no damages. Transportation damages should immediately be reported to the one responsible for the transport Damages, faults and eventually missing details should immediately be reported to the seller. Take care of the packing material so that small children cannot play with it. Placement The hood is to be mounted on the wall. When installed, the hood must be not less than 50 cm. 3). Min 50 cm Min 75 cm Electrical connection The hood has a power cord with moulded plug with earth connection to be connected to a wall outlet of 230 V. The power outlet should be pre-mounted in such a way that the power cord is invisible when the hood is fully mounted. As it is then hard to disconnect the power plug for cleaning and service, an easy accessible two pole switch should be fitted. The switch should conform to regulations with an opening distance between contacts of not less than 3 mm. Fig. 3 5 Mounting of hood q Fit the drilling scheme onto the wall at the right height. 4) The lower edge of the scheme correspond to the lower edge of the cooker hood. q On the drilling scheme is printed a line corresponding to the centre of the appliance; with a pencil draw a line up to the ceiling, this will aid installation procedures. 4) q Drill as indicated on the scheme and fit two dowels, two hooks and two screws 5x45. 4 q Hang the hood, adjust the position using the screws on the hooks of the hood. 5 q From the inside of the hood mark on the wall the point corresponding to the hole which will be used to fix definitively the hood. q Drill two hole (Ø 8mm) and fit two dowels. q From inside of the hood insert the definitive fixing screws. 6 6 q Dismount the chimney support from the chimney unscrewing the two side screws (one per side of the chimney- conserve them). [. . . ] 8), to mount proceed in reverse order. Fig. 10 Changing the lighting elements q With the help of a screwdriver remove the screw that secures the lamp cover (Fig. q Replace the damaged part with one of equal rating. q Mount the lamp cover and secure it with the screw. Cleaning To clean the outside of the hood use a cloth moistened with denatured alcohol or neutral liquid detergents. [. . . ]