User manual AEG-ELECTROLUX EFC9426X-S

[. . . ] Instruktionsbok, Bruksanvisning, Brugsvejledning EFCR 942 EFC 9426 - 6426 Käyttöohje, User Manual, Gebrauchsanweisung S N DK FIN UK D S N DK FIN UK D Innehållsförteckning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Innholdsfortegnelse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Indholdsfortegnelse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Sisällysluettelo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the hood is connected to the recirculation system an active carbon filter needs to be used. A Fig. 2 A B CDE F G H I Control Panel The best results are obtained using low speed with normal cooking and a higher speed in the case of a particular concentration of fumes. We advise switching the hood on a few minutes before starting to cook so as to obtain a vacuum in the kitchen and to leave it working at the end of cooking for another 15 minutes until all fumes and odours have disappeared. The commands are on the front panel of the hood. A Motor switch-off key B Hood switch-on key and speed selection 12-3-1-2 C 1st speed indicator 1 (LED) D - 2nd speed 2 and saturation of the anti-fat filter indicator (LED) E Intensive speed indicator F Intensive speed key (LED). If the hood is working when intensive speed is started, it will return to the previously set speed once the time has passed (5 minutes). If the hood is off when intensive speed is started, it switches off automatically at the time limit (5 minutes). It is, for example, opportune to use intensive speed to evacuate odours after finishing cooking. If the hood or the commands are not working, disconnect the electricity supply for at least 5 minutes and start the apparatus again. has to be used with the carbon filter: Press keys B and G simultaneously for three seconds. The D anti-fat filter LED lights up and then the E carbon filter LED as well. The LED that signals the saturation of the active carbon filter has been activated. Press keys B and G simultaneously for three seconds until the E carbon filter LED switches off. Grease filter LED (D) The D LED begins to flash when the anti-fat filter needs to be washed. The anti-fat filter must be changed after about 40 hours of use. Follow the instructions for changing the anti-fat filter. The active carbon filter LED (E) The E LED begins to flash when the active carbon filter must be changed. The anti-fat filter must be changed after about 160 hours of use. Follow the instructions for changing the active carbon filter. Restoring the saturation indicator After having carried out maintenance on the filter, keep key A held for 3 seconds until the LED of the anti-fat filter D or the LED of the carbon filter E stops flashing Attention!Restoring the saturation indicators MUST be carried out with the hood set in Standby and therefore without disconnecting the hood from the power supply. Control device of the saturation of the anti-fat and active carbon filters. The aspiration hood is equipped with a device that signals when the anti-fat or active carbon filter (recirculation with carbon filter version) needs cleaning. The hood is delivered from the factory without the carbon filter and therefore the LED that signals filter saturation is inactive. Activate the LED as indicated below if the hood Correct ventilation A vacuum must be created in the kitchen for the correct functioning of the hood. It is important to keep the kitchen windows closed and have a window open in an adjacent room. Important 45 If the hood is used together, for example, with an open fireplace that takes air from inside the house, a draught might occur that could bring fumes into the room. · Normally the filter is changed every 4 months. Fig. 4 46 Changing the lamp The hood must be disconnected from the power supply when changing the lamp. [. . . ] Slide the lower section of the flue downwards and insert it into the apposite housing on the upper part of the hood. 1 3, 5 x 13 a b 3 b 2 c 3, 5 x 13 d F 2, 9 x 6, 5 B Fig. 10 Mounting the grease filter Position the filter at the back of the hood and move the handle upwards until the filter is blocked. 50 Connection to external motor Concerns only the EFCR 942 model. The hood is not equipped with an internal motor and must be connected to an external motor (to purchase separately). The electrical connection must be carried out with the help of suitable connections. [. . . ]