User manual AEG-ELECTROLUX EFC9510X/CH

[. . . ] 11 Avvertenze per la sicurezza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Istruzioni per l'Uso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 MANUTENZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Filtri antigrasso metallici . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This is to ensure the correct vertical alignment of the various parts. · Fixing the wall brackets item 2: a) Place one of the brackets 2 against the wall approximately 1 or 2 mm from the ceiling or from the top limit, aligning its centre (slot) with the vertical line. b) Mark the centres of two keyholes in the bracket on the wall. c) Rest the other bracket 2 against the wall, aligning it with the vertical line, at a distance X measured as shown in fig. 2 equal to the height of the upper chimney element S supplied with the hood. The position X may vary, according to the various sizes of upper chimney element available. d) Mark the centres of the keyholes in the bracket on the wall. · Drilling fixing holes item 1: a) Mark a point on the vertical line at a distance from the cooking appliances of: d =982 min. b) At the point marked, draw a horizontal line parallel to the cooking appliances. c) Drill two holes in the wall 1 using an 8 mm drill bit (fig. 2), and insert the rawl plugs and screws into the holes 1 (4. 2 x 44. 4 screws). Fix the screws, leaving a space of 5-6 mm required to hook up the canopy. Small adjustments can be made using the hood adjustment screws (see Fitting the canopy). The hood should have a maximum excursion of 20 mm. 2 1 232 X 1 260 20 d = 982 min Fig. 2 16 GB Fixing the canopy Before starting to fix the canopy it will be necessary to adjust the support brackets S1 by turning the adjustment screws in a clockwise direction until their reach their limit (Fig. 3): a) Hook the canopy onto the two size 4. 2 x 44. 4 screws 1 fitted as described above (Fig. 4 ). b) Level the hood by turning the adjustment screws and then locking them. Fig. 3 S1 S1 Electrical connection and working test · Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. · Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. · Once the electrical connection has been completed, check that worktop illumination, motor and speed work properly. Fig. 4 1 1 Ducting or Recirculation fitting · Ducting fitting · The hood can be ducted to the outside using either rigid or flexible ducting Ø 120 or 150 mm, the choice of which is left to the installer. When 120 mm ducting is to be used it will be necessary to install the reduction flange item A on the air outlet (fig. 5). 1 Fig. 5 A GB 17 · When ducting the hood through the side air outlet from the lower chimney element I it is necessary to insert deflector D into spigot R to close off the opening that is not being used (fig. 6). · Cut the additional spigot P in correspondence with outlets 1 and 2 , which must be formed directly on the piece. [. . . ] It is recommended to use a damp cloth and mild liquid household cleaner. Fig. 13 GB 23 Quest'apparecchio é conforme alla norma europea sulla bassa tensione C. E. E. 73/23 relativa alla sicurezza elettrica e alle norme europee: C. E. E. 89/336 relativa alla compatibilità elettromagnetica e C. E. E. [. . . ]