User manual AEG-ELECTROLUX EFC9510XCH

[. . . ] · Never use the hood for purposes other than for which it has ben designed. · Never leave high naked flames under the hood when it is in operation. · Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. · Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. [. . . ] · Remove any activated charcoal filters. Lateral air exhaust on ducted version (connection to exhaust flue above wall cupboards) · Assemble the half-shells of the hood body extension piece 14. · Push fit the assembled hood body extension 14 onto the air exhaust outlet. · Insert the deflector 16 into the air exhaust fitting 15 to close off the unused outlet. · Push fit connection piece 15 to the hood body extension piece 14, ensuring that the free end matches up with the opening of the required outlet duct. · Remove any activated charcoal filters. ø 150 9 ø 120 15 14 16 GB 15 RECIRCULATION VERSION AIR OUTLET · Assemble the two halves of the hood body extension piece 14. · Push fit the assembled hood body extension piece 14 onto the air outlet. · Push fit connection 15 onto the hood body extension piece 14. · Insert the connection extension pieces laterally 14. 1 in connection 15. · Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. If this is not the case, adjust the position by either reversing the connection extension pieces 14. 1 or by cutting the hood body extension 14 along one of the thinner section channels denoting the pre-fixed lengths, then reassemble as described previously. · The air outlet directional grills 8a - 8b must be fitted after the lower outlet duct has been installed. · Ensure that the activated charcoal filters have been inserted. 15 8b 14. 1 8a 14 ELECTRICAL CONNECTION · Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. Flue assembly Upper exhaust flue · Slightly widen the two sides of the upper flue and hook them behind the brackets 7. 2. 1, making sure that they are well seated. · Secure the sides to the brackets using the 4 screws 12c (2, 9 x 9, 5) supplied. Lower exhaust flue · Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated. · Fix the lower part laterally to the hood body using the 2 screws 12c (2, 9 x 9, 5) supplied. · On the recirculation version, fit the directional grids 8a ­ 8b in their housings making sure that the directional symbols are towards the top and front of the hood. Also make sure that they are correctly inserted in the connection extension pieces 14. 1. 12c 7. 2. 1 12c 2. 1 2 8b 2. 2 8a 12c GB 16 USE Control panel L S1 M V1 V2 S2 V3 L S1 S2 M V1 V2 V3 Light Led Led Motor Speed Speed Intensive speed Switches the lighting system on and off. Flashes when the grease filters are saturated. Flashes when the activated carbon odour filters are exhausted. Switches the extractor motor on and off at low speed. Used to provide a continuos and silent air change in the presence of light cooking vapours. [. . . ] · Replace the Support, fixing it in place with the two Screws removed as above. GB 19 Quest'apparecchio è conforme alla norma europea sulla bassa tensione C. E. E. 73/23 relativa alla sicurezza elettrica e alle norme europee: C. E. E. 89/336 relativa alla compatibilità elettromagnetica e C. E. E. This appliance conforms to European Low Voltage Directive 73/23/CEE governing electrical safety, European Directive 89/ 336/CEE on Electromagnetic Compatibility and Directive 93/68/CEE regarding CE Marking. [. . . ]