User manual AEG-ELECTROLUX EFC9542U

[. . . ] USE · · · · The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells. Never use the hood for purposes other than for which it has ben designed. Never leave high naked flames under the hood when it is in operation. Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. [. . . ] · Insert the connection extension pieces laterally 14. 1 in connection 15. · Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. · Connect the air outlet connection 15 to the hood body outlet using either a flexible or rigid pipe ø 150 mm, the choice of which is left to the installer. · Ensure that the activated charcoal filters have been inserted. 15 14. 1 ø 150 EN 1 19 ELECTRICAL CONNECTION · Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. · Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. Flue assembly Upper exhaust flue · Slightly widen the two sides of the upper flue and hook them behind the brackets 7. 2. 1, making sure that they are well seated. · Secure the sides to the brackets using the 4 screws 12c (2, 9 x 9, 5) supplied. · Make sure that the outlet of the extensions pieces is aligned with the chimney outlets. Lower exhaust flue · Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated. · Fix the lower part laterally to the hood body using the 2 screws 12c (2, 9 x 9, 5) supplied. 2. 1 2 12c 12c 2. 2 12c EN 2 20 USE L T1 T2 T3 T4 T5 F The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button . Touch control Basic functions Dual Function When briefly pressed it switches the lighting system on and off. When pressed for 2 seconds it starts the lighting system in "courtesy light" mode. The lamps are fed at a reduced power of approximately 5W. Such function can be stopped by pressing the touch control for 2 seconds or just by pressing it shortly in order to return to the normal lighting mode. In courtesy light mode the touch control is not lit. When pressed the motor is stopped, regardless of the speed it is set to. When pressed the motor is set to the first speed By a brief pressing the motor is set to the second speed. By pressing the touch control for approximately 2 seconds the Delay function is enabled, i. e delayed shutdown of the appliance ensuring a complete elimination of the residual odours. This function can be activated at OFF-position and at 1°, 2° and 3°speeds. It can be stopped in advance by pressing any of the touch controls (T) with the exception of T3. The Delay function works according to the following scheme: 1°speed / OFF = 20 minuets 2°speed = 15 minutes 3°speed = 5 minutes When pressed the motor is set to the third speed Indicator lights Touch control unlit Touch control lit Lights off Lights on L Touch control unlit Courtesy light on T1 T2 T3 Touch control lit Touch control unlit Motor on Motor off Touch control lit Touch control lit Flashing touch control Second speed on Delay function on T4 Touch control lit EN 2 21 Touch control Basic functions Indicator lights T5 F When pressed the motor is set to the intensive speed timed to 5 minutes. At the end of 5 minutes of intensive speed the hood starts again at the speed it was set Touch control lit to previously. In case the hood is set to the intensive speed directly from OFF-state it will then start from the first speed after 5 minutes of intensive speed. Touch control lit Metal grease filters satuWhen pressed for 4 seconds it resets the filter alarm ration alarm. [. . . ] · Remove the snap-on lamp cover by levering it from under the metal ring, supporting it with one hand. · Remove the halogen lamp from the lamp holder by pulling gently. · Replace the lamp with a new one of the same type, making sure that you insert the two pins properly into the housings on the lamp holder. · Replace the snap-on lamp cover. EN 2 24 Dir. [. . . ]