User manual AEG-ELECTROLUX EFC9620X

[. . . ] Wir wnschen eine gute Zeit. ES Bienvenido al mundo Electrolux Gracias por elegir un producto Electrolux de primera clase, el cual esperamos le proporcione una gran satisfaccin en el futuro. Electrolux ambiciona ofrecerle una amplia variedad de productos de calidad que haga su vida ms cmoda. Usted encontrar algunos ejemplos en la portada de este manual. Por favor, tmese unos minutos para estudiar este manual de modo que pueda aprovecharse de los beneficios de su nueva mquina. [. . . ] Maintenance Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified time period. Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Characteristics electrolux 7 CHARACTERISTICS Dimensions EN 8 electrolux Characteristics Components Ref. Q. ty Product Components 1 Hood Body, with: Controls, Light, EN 1 Blower, Filters 2 1 Telescopic Chimney: 2. 1 1 Upper Section 2. 2 1 Lower Section 9 1 Reducer Flange 150-120 mm 10 1 Flange 150 15 1 Air Outlet Connection Ref. Q. ty Installation Components 7. 2. 1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4, 2 x 44, 4 12c 6 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual 9 15 12a 7. 2. 1 11 10 2. 1 2 2. 2 12c 11 12a 1 Installation electrolux 9 INSTALLATION Wall drilling and bracket fixing Wall marking: Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. Draw a horizontal line at 650 mm above the hob. Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre with the vertical reference line (distance between the hole and the vertical line: 132, 5 mm on both side of the line). Mark the wall at the centres of the holes in the bracket. Place bracket 7. 2. 1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre with the vertical line (distance between the hole and the vertical line:132, 5 mm on both side of the line). Mark the wall at the centres of the holes in the bracket. Mark a reference point as indicated at 116 mm from the vertical reference line and 306 mm above the horizontal reference line. Repeat this operation on the other side. Drill 8 mm holes at all the centre points marked. Fix the lower bracket 7. 2. 1 using the 12a screws (4, 2 x 44, 4) supplied. Fix the upper bracket 7. 2. 1 (and, in case of hood installation in recycling version, the air outlet connection 15) using the 2 screws 12a (4, 2 x 44, 4) supplied. Insert the two screws 12a (4, 2 x 44, 4) supplied in the hood body fixing holes, leaving a gap of 5-6 mm between the wall and the head of the screw. EN 15 11 12a 116 116 306 650 min. X 7. 2. 1 132, 5 132, 5 12 10 electrolux Installation Hood body installation Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. EN Hook the hood body onto the screws 12a. Adjust screws Vr to level the hood body Vr 12a Connection in Ducting Version When installing the ducting version, connect the hood to the chimney using either a flexible or rigid pipe 150 or 120 mm, the choice of which is left to the installer. To install a 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. [. . . ] Replace the Filter Pull the Comfort Panel to open it. Remove the saturated charcoal filter, turning the fasteners provided. Fit the new filter and fasten it its correct position. Put the metal grease filters in their seats. [. . . ]