User manual AEG-ELECTROLUX EFC9690X

[. . . ] 18 The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. Environmental information. electrolux safety warnings 5 GB Safety warnings For the user · The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. · Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. [. . . ] It is important to keep the kitchen windows closed and have a window in an adjacent room open. · The hood is equipped with a "TOUCH SENSOR" device able to TOUCH SENSOR determine the control of the lights and the speed when the user touches the control bar. Read the instructions below carefully for this purpose. Automatic switch-on function The hood is equipped with a temperature sensor that starts the motor at the 1st suction speed (power) when the room temperature around the hood is higher than 70°C. The user can, however, switch off or modify the suction speed (power). (See paragraph "Control of suction speed Control Contr (power)"). (power) electronic The hood is fitted with an electronic over-charge protection over-charge protection system: in the event of an excessive charge on the mains supply network, the electronic electronic system goes into protective protective mode and the Neon light off; reset switches off; to reset simply switch off off the Neon and then on again control. using the hood control. electrolux control panel 9 Control of suction speed (power) The selection of the suction speed (power) is cyclical, according to the speed sequences ""stand-by - 1-2-34- Stand by -1-2-". . . so that at every touch of the UPPER PAR of the PAR ART control bar the suction speed (power) increases by a level and then switches off (stand-by) if the control bar is touched again when the hood is at suction speed (power) 4. It is possible to turn the hood off (standby) even when the hood is at any speed by pressing the UPPER PART of the control bar (for more than ART 3 seconds). Control Control bar GB PAR ART UPPER PART LED PAR ART LOWER PART 10 electrolux electrolux control panel GB It is possible to determine what suction speed (power) the hood is in when the bar is equipped with a led that changes colour on the basis of the suction speed (power), as follows: · Hood in stand-by: LED OFF · 1st suction speed (power) - led GREEN · 2st suction speed (power) - led ORANGE (amber) · 3st suction speed (power) - led RED · 4st suction speed (power) - led RED (FLASHING) Note: the 4th suction speed (power) remains on for 5 minutes, after which the suction motor switches off (Stand-by) Touched once more, the suction motor switches off (Stand-by). Control bar visual signal : · Need to wash the anti-fat filter: GREEN led FLASHING (read the instructions relative to "Reset and configuration of the filters saturation signal") · Need to wash or replace the carbon replace filters: ORANGE (amber) led FLASHING (read the instructions relative to "Reset and configuration of the filters saturation signal") Note: reset can be carried out with the control lever. Control Control bar PAR ART UPPER PART LED PAR ART LOWER PART Control of the central and side lights The central light can be accessed and switched off by touching THE LOWER PART of the control bar BRIEFLY. Control of the Neon light The neon light can be accessed and switched off by touching THE LOWER PART of the control bar IN A PROLONGED MANNER. electrolux control panel 11 Reset and configuration of the filters saturation signal Switch the hood on at any speed (see paragraph above "Selection of the suction speed (power)" Reset anti-fat filter saturation signal (GREEN LED FLASHING on the control control level) proceed First proceed with the maintenance of the filter as described in the corresponding corresponding paragraph. Touch in a prolonged manner (more than 3 seconds) the UPPER PART of the control lever, the LED stops flashing to indicate that the reset of the signal has been carried out and the hood switches off. Reset anti-fat filter saturation signal ORANGE (amber) LED FLASHING proceed First proceed with the maintenance of the filter as described in the corresponding corresponding paragraph. Touch in a prolonged manner (more than 3 seconds) the UPPER PART of the control lever, the LED stops flashing to indicate that the reset of the signal has been carried out and the hood switches off. Deactivating the carbon filter saturation signal (for special applications) Switch the hood off (see paragraph above "Select the suction speed power") Touch in a prolonged manner (more than 5 seconds) the UPPER PART of the control lever, the LED flashes in GREEN (amber) to indicate that the carbon filter saturation signal has been deactivated. To reactivate the carbon filter saturation signal, repeat the operation. The LED flashes in ORANGE. GB · Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds. After reconnecting the power supply wait 15 seconds and then check that the cooker hood is now operating correctly. 12 electrolux electrolux maintenance and care Maintenance and Care GB · Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. through Or if the appliance has been connected through a plug and socket, then the removed from plug must be removed from the socket. grease Metal grease filter · The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function. · Clean the inner housing using a hand hot solution only(never use caustic detergents, abrasive powders or brushes). · Turn the internal bolts a ¼ turn to access the side filters. · Carry out the montage following the procedure described above in the reverse sequence. Metal grease filter Active charcoal filter 14 electrolux electrolux maintenance and care GB Dismantling and mounting the filter in the upper part of the hood · With a small screwdriver lift the 3 tongues that block the filters and remove the filters. · Remove the frame that blocks the active carbon filter. · Carry out the montage following the procedure described above in the reverse sequence. [. . . ] The switch must be accessible at all times. The following is valid in the United Kingdom only: - the wire which is coloured green and yellow must be connected to the terminal which is marked with the ), letter E or by the earth symbol ( or coloured green or green and yellow; - the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. GREEN & YELLOW 5AT BROWN BLUE CORD CLAMP IMPORTANT!Power cable repalcement must be undertaken by the authorized IMPORT service assistance centre in order to prevent any risks. 20 electrolux electrolux installation Installation GB Make sure that the cooker hood is disconnected from the power supply before carrying out the installation. Before installing the hood, remove the metal bracket and the wooden plank fixed to the upper part that are part of the packing. Dispose of the packing in accordance with the regulations in force. If you want to install a telescopic flue kit (optionally purchased as a special accessory, see "special accessories" chapter), read the instructions sent with the kit carefully. electrolux installation 21 · To make mounting easier, trace a median line and two dots on the wall in correspondence to the hooks and then make holes in the wall. · Insert the hooks and wall dowels into the holes, hang the hood on the hooks and fix them with the metric screws. GB The line marked in the delimited area must have a connector. [. . . ]