User manual AEG-ELECTROLUX EFC9710.1

[. . . ] CX-L-410-xx 06067710 DUNSTABZUGSHAUBE CAPPA D' ASPIRAZIONE COOKER HOOD HOTTE ASPIRANTE MONTAGE UND GEBRAUCHSANWEISUNG MANUALE D'INSTALLAZIONE, D'USO E MANUTENZIONE INSTALLATION, USE AND MAINTENANCE MANUAL MANUEL D'INSTALLATION, D'EMPLOI ET D'ENTRETIEN FILTRANTE FILTERING UMLUFTBETRIEB FILTRANTE 1. ASPIRANTE SUCTION ABLUFTBETRIEB ASPIRANTE Cm 65 MIN 2. 3. 4. 5. B 6. 7. = 1 3 4 2 1-2-3-4 a - 180° b 1 3 4 2 c d 1-2-3-4 + 180° 8. 0 20 20 0 9. 1. 2. 3. 10. a 0 T _ + 0 T _ + P b 11. 12. a b 13. 14. · · · · estrarre la lampada difettosa; prendere la nuova lampada evitando di toccarla direttamente con le dita, per es. arrotolandola con carta; infilare i due spinotti della lampada nei fori appositi; rimontare la cornice del faretto. COOKER HOOD 1 GENERAL The model you have selected is a decorative suction cooker hood which can also work as filtering hood. A SUCTION HOOD extracts air, fumes and vapours from the inside environment and then expels them outside. It is not necessary to use carbon filters for purifying. [. . . ] 3. 4 MOUNTING THE ISLAND COOKER HOOD WITH EXTERNAL CHIMNEY The island cooker hood is intended to be mounted either directly on the kitchen ceiling or onto a stable suspended false ceiling structure. Check that the minimum distance between the bottom of the hood and the upper part of the hob is in conformity with indications in par. 4. 2 ELECTRICAL TECHNICAL DATA The electrical technical data are visible inside the hood after the removal of the grease filters. 4. 3 CONNECTION TO THE POWER SUPPLY The flexible feed cable supplied is already connected internally and emerges from the hood near the air outlet duct. It is possible to effect two types of electric installation: · fixed installation; · installation by means of plug on a socket. 4. 4 BEFORE ELECTRICAL INSTALLATION Before connection you must: · check that the electrical data indicated are in conformity with the main voltage and frequency values of the building where the hood is to be installed; · check that the building is fitted with electric safety systems to protect against short circuits and electric shock systems, according to the laws in force; · install an electric socket (or connection point) with a bipolar switch, which has contacts with an opening of at least 3 mms; · if it is intended to install the hood with a plug, it is necessary that you have access to the plug. · always turn off the main voltage supply by means of the bipolar switch before connecting and switch on again only when connections have been completed, tested and are safe. · · · · · · not to cook "flambé" dishes, avoid flames directly underneath the hood; to avoid leaving on any hot plates which generate strong free flames underneath the hood; to avoid any strong flames being issued from under saucepans at the sides; when frying, not to allow oil to splash or overheat in the pan, as this is a fire risk; before any cleaning or maintenance operation, disconnect the hood from the main supply, by means of the main switch or the bipolar switch or by removing the plug; if other gas equipment or equipment which consumes oxygen from the environment is used, ventilation must be sufficient. For safe ventilation, maximum depression in the room should not exceed 4 Pa (0, 04 mbar) and there must be a hole on the outside facing wall (suitably positioned and dimensioned); never use the hood without the grease filters; keep the grease filters clean, taking into account the recommended cleaning suggestions; replace the carbon filters (if the hood is used as a filtering hood), as indicated; turn on the hood motor before you start cooking; turn off the hood motor about 10 minutes after you have finished cooking; do not use the hood to suction gas, fumes, vapours or other substances different from the normal fumes in the kitchen. 7 FUNCTION AND USE In FIG. 11 you see the 2 different kinds of controls: FIG. 11a: soft touch control with display; see par. FIG. 11b: soft touch control with led points and push buttons screenprinted on s/steel. 7. 1. 1 SOFT TOUCH CONTROL WITH DISPLAY AND BUTTONS (FIG. 11a) The activated functions are listed as follows: LIGHTS: to switch the lights on or off; (pressure inf. to 1 second); MOTOR OFF: turn the motor off; TIMER: if pressed when the hood is already functioning with one of the pre-established speeds, timing is activated, that is a count down of 15 minutes, after which the motor stops. During this time the display indicates the speed number and the point led flashes; O T + P reduces the speed of the motor; increases the speed of the motor; INTENSIVE SPEED: the intensive speed is the highest motor speed. It is automatically excluded after 5 minutes and the hood goes back to the 2rd speed. 5 PRECAUTIONS TO BE TAKEN IF REPAIRS ARE TO BE CARRIED OUT Repairs, including the replacement of the feed cable if necessary, are to be carried out only by qualified personnel, using standard methods, instruments and materials. Any repairs carried out by others could prove to be dangerous and could be a fire risk. DISPLAY MEANING OF THE SYMBOLS: The functions activated by the push buttons are as follows: LIGHTS: switch the lights on and off; STAND_BY: The motor of the hood is off; . . . . . first, second , . . . . speed; O + MOTOR OFF: turn the motor off; reduces the motor speed; increases the motor speed; intensive speed activated; flashing led point: the timer is in action; (FLASHING F LETTER) grease-filters should be cleaned; only in case of filtering hood (flashing C letter) carbon filters should be replaced. 7. 1. 2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTERS The electronic controls with display allow automatic control of the grease filters and the carbon filters (only when the hood is used in the filtering version), so that the user does not have to remember when maintenance was last carried out. When the metallic grease filters have to be cleaned, the letter F on the display will flash. When the carbon filters have to be replaced, the letter C on the display will flash. It is possible to consult the electronic system concerning how clean the grease filters are and how worn the carbon filters are, as follows: stop the motor and . . . to find out how clean the fat filters are, press the O and - buttons at the same time. On the display, a number between 0 and 9 will appear, the smaller the number, the dirtier the filter is; . . . [. . . ] To ensure correct ventilation and air interchange in the kitchen, national and international regulations exist, which should be respected. The manufacturer denies any responsibility for fires caused by failure to replace the carbon filters. Always replace the lamps with lamps which have the same electrical characteristics (see TECHNICAL DATA). Before replacing the lamps, make sure that they are cold and that power has been completely turned off. [. . . ]