User manual AEG-ELECTROLUX EFCI90542X

[. . . ] USE The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells. Never use the hood for purposes other than for which it has ben designed. Never leave high naked flames under the hood when it is in operation. Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. [. . . ] Before tightening the screws completely it is possible to adjust the frame by turning it. Make sure that the screws do not come out of their seats in the slotted holes. The frame mountings must be secure to withstand the weight of the hood and any stresses caused by the occasional side thrust applied to the device. On completion, check that the base is stable, even if the frame is subjected to bending. In all cases where the ceiling is not strong enough at the suspension point, the installer must provide strengthening using suitable plates and backing pieces anchored to the structurally sound parts. 1 1 2 2 Ducted version air exhaust system Connection When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe 150 or 120 mm, the choice of which is left to the installer. To install a 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. Fix the pipe using the pipe clamps 25 provided. Remove any activated charcoal filters. 150 120 25 25 9 EN 9 9 Recirculation version air outlet Fix the connection 15 to the frame using the 4 screws provided. Fix the flange 10 to the lower opening of the connection 15. Connect the hood air outlet to the flange in the lower part of the junction using a rigid or flexible 150 tube (by installer's choice). 10 15 Flue assembly - Mounting the hood body Position the upper chimney section and fix the upper part to the frame using the 2 screws 12c (2, 9 x 6, 5) provided. Similarly, position the lower chimney section and fix the lower part to the frame using the 2 screws 12c (2, 9 x 6, 5) provided. Before fixing the hood body to the frame: Remove the grease filters from the hood body. From below, use the 4 screws 12f (M6 x 10)provided to fix the hood body to the frame. 12c 12c 12f EN 1 10 0 ELECTRICAL CONNECTION Connect the Hood to the Mains power supply, inserting a two-pole Switch with a contact aperture of at least 3 mm. Remove the Metal grease filters (see par. on "Maintenance") and make sure that the power supply Cable is properly inserted in the Suction fan socket. Take the wires indicated in fig. 1 and pass them through the slot formed on the galvanized diffuser support, as shown in fig. 2. 1 2 Position the finishing plug 27 over the housing in the diffuser support, fixing it using a screw 12e (2. 9 x 9. 5) and applying the 2 cable clamp elements 26 as indicated in figs. 3 and 4. 4 3 Connect the Controls Connector fig. Store both the Connectors in the Protective box 24 and close it with 2 Screws 12e (2. 9 x 9. 5), provided. 6 5 Remove the protective film from the double-sided adhesive on the connection box, and fix it inside the motor compartment fig. 7. 7 EN 1 11 1 USE L T1 T2 T3 T4 T5 F The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button . Touch control Basic functions Dual Function When briefly pressed it switches the lighting system on and off. When pressed for 2 seconds it starts the lighting system in "courtesy light" mode. The lamps are fed at a reduced power of approximately 5W. Such function can be stopped by pressing the touch control for 2 seconds or just by pressing it shortly in order to return to the normal lighting mode. [. . . ] By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. El smbolo en el producto o en su embalaje indica que este producto no se puede tratar como desperdicios normales del hogar. Este producto se debe entregar al punto de recoleccin de equipos elctricos y electrnicos para reciclaje. Al asegurarse de que este producto se deseche correctamente, usted ayudar a evitar posibles consecuencias negativas para el ambiente y la salud pblica, lo cual podra ocurrir si este producto no se manipula de forma adecuada. [. . . ]