User manual AEG-ELECTROLUX EFCR950U

[. . . ] 29 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Inhalt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Contents Information about safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Description of the hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] We advise switching the hood on a few minutes before starting to cook so as to obtain a vacuum in the kitchen and to leave it working at the end of cooking for another 15 minutes until all fumes and odours have disappeared. The commands are on the front panel of the hood. A Motor switch-off key B Hood switch-on key and speed selection 1-23-1-2 C 1st speed indicator (LED) D - 2nd speed and saturation of the anti-fat filter indicator (LED) E 3rd speed and saturation of the anti-fat filter indicator (LED) F Intensive speed indicator G Intensive speed key (LED). If the hood is working when intensive speed is started, it will return to the previously set speed once the time has passed (5 minutes). If the hood is off when intensive speed is started, it switches off automatically at the time limit (5 minutes). It is, for example, opportune to use intensive speed to evacuate odours after finishing cooking. If the hood or the commands are not working, disconnect the electricity supply for at least 5 minutes and start the apparatus again. G H I Activate the LED as indicated below if the hood has to be used with the carbon filter: Press keys B and G simultaneously for three seconds. The D anti-fat filter LED lights up and then the E carbon filter LED as well. At this point the LED that signals the saturation of the active carbon filter has been activated. Press keys B and G simultaneously for three seconds until the E carbon filter LED switches off. Grease filter LED (D) The D LED begins to flash when the anti-fat filter needs to be washed. The anti-fat filter must be changed after about 40 hours of use. Normally the filter is changed every 4 months. · Remove the carbon filter by unscrewing the two screws that fix it and pulling downwards. Do not for get to clean the filter periodically. · Follow the instruction in reverse to disassemble the filter. · Always indicate the model, and the product and series number when you need to order new filters. The relative data are indicated on the plate inside the apparatus. · Active carbon filters can be ordered from your 4 2 local dealer. Fig. 5 Changing the lamp The hood must be disconnected from the power supply when changing the lamp. 5: · Remove the protective glass of the lamp with a screwdriver. · Substitute the lamp with an equivalent one. · Remount the protective glass of the lamp. Fig. [. . . ] In the case of using a non-return valve, check that it functions correctly and is not blocked by the tube. · Insert the plug into the power supply socket. · Remove the screw that joins the two external sections of the flue. · Slide the lower section of the flue downwards and insert it into the apposite housing on the upper part of the hood (Fig. [. . . ]