User manual AEG-ELECTROLUX EFCR956X

[. . . ] 37 Extractor version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Filter Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Control Panel - EFC 6940 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Control Panel - EFC 1410 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Static red light : Hood is switched on at power level 3 (maximum). Alternating red light : Hood is switched on at intensive power level (timed at 5 minutes) Alternating green light : Indicates the grease filter saturation - clean the grease filter Alternating orange light : Indicates the charcoal filter saturation - clean or replace the charcoal filter Attention!The control Ball flashes orange to indicate the saturation of the odor filter even when the charcoal filter is not installed inside the cooker hood. However perform the signal reset operation as follows: select the intensive speed (the control ball lights up with a red flashing light), depress again and hold depressed for about 3 seconds until a bip sound indicates the reset. depress towards the right to switch on the hood depress towards the left to switch on the light. Fig. 3 Control device for grease or charcoal filter The air duct, in this hood, is provided with a device that signals when the filter requires cleaning or changing . Led signal for grease filter The LED signal flickers (flickering green light) when the grease filter requires cleaning, occurs at about 40 operating hours. Carefully note the device for grease filter maintenance! Led signal for charcoal filter The LED signal flickers (flickering orange light) when the grease filter requires cleaning, occurs at about 160 operating hours. Carefully note the device for charcoal filter maintenance! Switching on the hood - Fig. 3 The control ball is a balancer switch. Depressing the control ball repeatedly towards the right switches on the hood and you may select the suction level desired, depressing once again on the right the hood switches off. Resetting the saturation indicator After cleaning or replacing the filter, select the intensive speed (the control ball lights up with a red flashing light), depress again and hold depressed for about 3 seconds until a bip sound indicates the reset. Switching on the light - Fig. 3 Depress the control ball towards the left : once for submersed lighting, once again for full lighting, depress again to switch off the light. Correct ventilation If the cooker hood is to work correctly there must be an under pressure in the kitchen. 7 41 What to do if If your appliance fails to work properly please carry out the following checks. Symptom The cooker hood will not start. . . The cooker hood is not working Solution Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected Check that: The fan speed is set high enough for the task. The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting and outlets are not blocked. The safety cut-out device has been tripped. Turn off the hob and then wait for the device to reset. If the hood has been installed below the heights indicated in the installation instructions the motor will cut-out frequently which will damage the hood. The cooker hood has switched off during operation. . . If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. [. . . ] The following is valid in the United Kingdom only: - the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol ( ), or coloured green or green and yellow; - the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. 45 Installation Wall unit mounting - Fig. 9-10-11-12-13 First decide which functioning version is better for you. If you decide to use the hood in exhausting version we suggest to position the upper section of the chimney so that the oulet slots are not visible once installation has ended, on the contrary if is decided to use the hood in recycling version BE SURE that the side with slots is up (see also A-B-C sequence on on Fig. Assembling the chimney flue support/bracket (3 parts): The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the telescopic chimney flue. [. . . ]