User manual AEG-ELECTROLUX EFI625G

[. . . ] When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ring surfaces: electric cookers 550 mm gas cookers 650 mm The national Standard on fuel-burning systems specifies a maximum depression of 0. 04 mbar in such rooms. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed. The air outlet installation must comply with the regulations laid down by the relevant authorities. [. . . ] Never use corrosive, abrasive or flammable cleaning products. Never insert pointed objects in the motors protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the control panel and filter grille using a damp cloth and delicate detergents. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Warning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Guides Grease filter The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. The synthetic filter is very thin (approx. 1 mm) and positioned on the inside of its related support grille. Remove the grid or the metal grease filter. Replace the old bulb with a new one of the same type. Remount the grid or the metal grease filter. If the light does not come on, make sure the bulb has been inserted correctly before contacting your local Service Force Centre. 9 Something Not Working If your appliance fails to work properly please carry out the following checks. The cooker hood is not working Solution Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected Check that: The fan speed is set high enough for the task. The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting and outlets are not blocked. The safety cut-out device has been tripped. Turn off the hob and then wait for the device to reset. [. . . ] For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC) or a suitably competent person. Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the 13 Installation Mounting accessories included 1 deflector 1 coupling ring Ø 100 mm (EFI 635) or Ø 120 mm (EFI 640) 2 plastic washers for the spacer 4 wall dowels (screw anchors) 2 screws 5 x 45 with cylindrical heads for use on walls (lower fixing) 2 screws 5 x 45 countersunk for wall use (fixing the hooks) 2 hooks 1 Allen wrench 1 screw 2. 9 x 9. 5 (ONLY EFI 635 - to affix the deflector on the outlet hole) 2 screws 3. 5 x 9. 5 (to affix the spacer to the cooker hood) 2 screws 4. 2 x 35 (ONLY EFI 635 - to fix the hood to the top of a wall cabinet) 2 screws 2, 9 x 13 (ONLY EFI 640 - to fix the deflector to the hood or to the top of a wall cabinet) 4 screws 4. 5 x 16 (to affix the cooker hood sideways) 8 screws 4. 5 x 13 (to affix a wooden panel to the cabinet door). I I Fig. 9 Ø 2, 5mm x 6mm max N3 J L L K 6mm Fixing a furniture door to the visor Remove the extraction grille. [. . . ]