User manual AEG-ELECTROLUX EFP643S

[. . . ] The hood must be installed at a minimum of 40 cm above an electric hob or cooker and at least 65 cm above gas burners or a gas cooker. During installation, make sure the electrical power supply cable is left completely free and in perfect condition. The electrical power supply to the hob is only cut off when the power supply cable is unplugged or the fuse is disconnected. The laws and regulations applicable to the method used for the vented air outlet must be observed. [. . . ] Once you have finished cooking, leave the hood on for another 15 minutes, or until all steam and fumes have disappeared. Care and Cleaning Before performing any hood care operations, turn off the electricity supply by unplugging the power supply cable from the wall socket or by removing the fuse. Cleaning the stainless steel surfaces For an improved cleaning action on the stainless steel surfaces of the hood, use a soft cloth and Original Steel Polish, on sale from the service centre. If the surface is extremely dirty, you can use methylated spirit. NEVER use scouring powder or any other product that may scratch the surface irreparably. Do not use materials such as steel wool or scraping pads which may scratch the surfaces. Hood cleaning Clean the exterior of the hood using a soft cloth moistened with a neutral detergent. Never use corrosive, abrasive or inflammable cleaning products. 34 Cleaning/replacing the charcoal filter Unlike other filters of the same type, LONG LIFE charcoal filters can be cleaned and re-used. The filter should be cleaned every other month under normal operating conditions. We recommend you clean the filter in a dishwasher, at the maximum temperature setting, using a standard detergent. No domestic tools should be in the dishwasher when the filter is cleaned, in order to avoid any food particle deposits on the filter that could create additional unpleasant odours. To reactivate the charcoal, just dry the filter inside your oven. Set the oven mode to normal (not to the "Grill" mode), at a maximum temperature of 100° C, and leave the filter inside it for 10 minutes. Read the filter instructions too. Clean the filter regularly. Remove the grease filter to access the data plate. 36 Technical Specifications Model Dimensions Height Width Depth Lighting Grease filter Electrical connection (Electric) Safety class Maximum absorbed power 460 mm 596 mm 315 mm max 2 x 20 W 1 230 V I 310 W 460 mm 596 mm 320 mm max 2 x 20 W 1 230 V I 310 W EFP 6446 EFP 6456 95 17 8 120 70 14 0 430 460 596 300 20185 -34 5 EFP 6456 95 17 13 120 70 14 0 430 460 596 15- 180 300 -34 5 EFP 6446 37 Installation Unpacking Make sure the hood is in perfect condition. The carrier must be notified immediately of any damage incurred during transportation. The retailer must be notified immediately of any damages, faults and any missing parts. Do not leave the packaging components within the reach of children. Positioning The hood must be installed in a wall cabinet. Make sure the back of the fan is not touching the wall in any place. This would affect its positioning and could cause the hood to become noisy. The hood must be installed at a minimum of 40 cm above an electric hob or cooker and at least 65 cm above gas burners or a gas cooker (see figure). Min 40 cm Min 65 cm Installing the hood in a cabinet The locking screws must be in place (x 2). If this is not the case, the hood could drop. Trace a line using the installation template to guide you (see figure 1). Saw along this line and cut a groove at the base of the top part of the cabinet. Measure the thickness of the cabinet walls (see figure 2). [. . . ] The hood is supplied with an electrical power supply cable fitted with a moulded plug with an earthing pin, suitable for a 230 V wall socket. Depth adjustment Once the hood has been installed, adjust it so that it is in line with the wall. Remove the filter as illustrated in the chapter entitled "Care and cleaning". Push the adjustment arms against the wall. Reposition the grease filter. 2 1 39 Fitting the cold air inlet This is not applicable when the hood is used in recirculation mode. [. . . ]