User manual AEG-ELECTROLUX EFV60380BX

[. . . ] Any user who does not adhere to these instructions is risking his own life and the lives of others. In this case, the manufacturer declines any responsibility (see FIG. 4) If the hood is used as a suction hood, it is necessary to guarantee enough airexchange for instance making a hole for ventilation on the outside wall by qualified personnel. In case it is used an ELECTROLUX COOKER HOOD in an low energy consumption house or in a house with confort air, it is necessary to follow the data of the producer, in order not to affect the air behaviour in a negative way. [. . . ] 1 WARNING The electrical connection can only be carried out by qualified professional personnel, using standard material and state of the art installation methods. The manufacturer declines any responsibility for installations carried out by unskilled persons and for installations which are not in conformity with the standard norms concerning electrical safety (both concerning methods and materials). 2 ELECTRICAL TECHNICAL DATA The electrical technical data are visible inside the hood after the removal of the grease filters. 3 CONNECTION TO THE POWER SUPPLY The flexible feed cable supplied is already connected internally and emerges from the hood near the air outlet duct. Check that the electrical data indicated are in conformity with the main voltage and frequency values of the building where the hood is to be installed; · Check that the building is fitted with electric safety systems to protect against short circuits and electric shock systems, according to the laws in force; · Install an electric socket (or connection point) with a bipolar switch, which has contacts with an opening of at least 3 mms; · If it is intended to install the hood with a plug, it is necessary that you have access to the plug. Always turn off the main voltage supply by means of the bipolar switch before connecting and switch on again only when connections have been completed, tested and are safe. Repairs, including the replacement of the feed cable if necessary, are to be carried out only by qualified personnel, using standard methods, instruments and materials. Any repairs carried out by others could prove to be dangerous and could be a fire risk. Before using for the first time, ensure that all the points in the previous paragraphs have been complied with. The hood is not proper for the use of children and people with reduced mental, physical and sensorial capacities unless they have been trained on purpose by the person responsible for their security. Children should be supervised to guarantee that they do not play with the hood. To activate the functions connected to these push buttons, it is necessary to apply a little pressure just lightly and for a short time. If pressure is too lengthy on the push buttons the connected functions are not activated. The functions activated by the push buttons are as follows: LIGHTS: switch the lights on and off; TIMER: if pressed when the hood is already functioning with 1st, 2nd, 3rd or 4th speed, the led point connected with the selected speed, starts to flash for 10 minutes, after which motor automatically stops. MEANING OF THE LED POINTS: if the leds connected with the speeds are flashing, there is a timing running. 1st Speed; 2nd Speed; 3rd Speed; 4th Speed; 5th Speed; led point is flashing; 6th Speed; led point is flashing. 5th and 6th Speed must be used just for short periods as the hood is taking in a big quantity of air so after 10 minutes the motor is automatically reset to the 3rd speed. 2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTER the electronic controls with led points allow automatic control of the grease filters and carbon filters (only in case the hood is used in filtering version) so that the user does not have to remember when maintenance was last carried out. When the grease filters require cleaning, an acoustic signal is issued for some seconds and the led point above the timer push button keeps on flashing. When the carbon filters need replacing or regeneration, an acoustic signal is issued for some seconds and the led point above the light push button keeps on flashing. TO PUT THE GREASE AND CARBON FILTERS CONTROL BACK TO ZERO To put the grease filter counter back to zero you must: · stop the motor; · Press the timer push button twice in succession, until you hear the acoustic signal. to confirm reset the led point stops flashing. [. . . ] It is important to follow the pattern of the satin finish with the cloth (see FIG. The cloth used should not have any buttons, zips, fasteners or anything else which could scratch the surface. The use of harsh abrasive or granular products, petrol, spirits or similar products which could damage the surface of the materiall, is severely forbidden. The manufacturer will not be responsible for any damages either functional or to the appearance of the hood, caused by cleaning operations carried out using unsuitable products or unsuitable methods. [. . . ]