User manual AEG-ELECTROLUX EGG689BK

[. . . ] Gas hob INSTRUCTION INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance Mod. EGG 689 35678-9002 GB Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 During Operation · This appliance has been designed for non professional purpose in private houses only. It is meant to cook edible foodstuff only and must not be used for any other purposes. [. . . ] If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. Never use steel wool pads or acids. Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM SOLUTION # There is no spark when lighting the gas $ Check that the unit is plugged in and the electrical supply is switched on $ Check that the RCCB has not tripped (if fitted) $ Check the mains fuse has not blown $ Check the burner cap and crown have been replaced correctly, e. g. after cleaning. # The gas ring burns unevenly $ Check the main jet is not blocked and the burner crown is clear of food particles. $ Check the burner cap and crown have been replaced correctly, e. g. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 5 Instructions for the Installer Engineers technical data Overall dimensions Width: Depth: 580 mm. Ignition HT Spark Spark Generator Spark Gap Ispra Control's BF 50046 230-240V 0. 6 YA T 120 Fixed Cut out dimensions Width: Depth: 550 mm. 470 mm. Semi-rapid Burner Heat Input Rapid Burner Heat Input Auxiliary Burner Heat Input 1. 9 kW (6483 BTU/HR) Supply connections Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. 2. 9 kW Natural Gas (9895 BTU/HR) 2. 7 kW L. P. G. Before making the cut out in the worktop ensure that the edges of the hob that are to be near either a side or rear wall have a minimum distance of 55 mm. between the edge of the hob and the wall. The minimum distance combustible material can be fitted above the hob is 400 mm. must be allowed from the edges of the hob. The minimum distance combustible material can be fitted directly above the hob is 700 mm. must be left between the side edges of the hob and any adjacent cabinets or walls. FITTING THE GAS HOB WITH A COOKER HOOD ABOVE Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED FO 0813 Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to R 1/2" (1/2 BSP male thread). [. . . ] The pressure reading should be nominally 20mbar and must be between 17 mbar and 25mbar. Turn off the burner supplies. 12 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. Method · · · · Ensure that the gas taps are in the 'OFF' position Isolate the hob from the electrical supply Remove all pan supports, burner caps, rings, crowns and control knobs. With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate LPG injectors. To adjust the gas rate With the aid of a thin bladed screwdriver completely tighten down the by pass adjustment screw. [. . . ]