User manual AEG-ELECTROLUX EGG7355

[. . . ] Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the hob in any way. The appliance must be installed at a minimum distance of cm. 50 from curtains or other combustible material. Where this appliance is installed in marine craft or in caravans, it shall not be used as a space heater. l l Never use plastic or aluminium foil dishes on the hob. [. . . ] SYMPTOM SOLUTION n There is no spark when lighting the gas u Check that the unit is plugged in and the electrical supply is switched on u Check that the RCCB has not tripped (if fitted) u Check the mains fuse has not blown u Check the burner cap and crown have been replaced correctly, e. g. after cleaning. n The gas ring burns unevenly u Check the main jet is not blocked and the burner crown is clear of food particles. u Check the burner cap and crown have been replaced correctly, e. g. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. 5 Instructions for the Installer Engineers technical data Overall dimensions Width: Depth: 685 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V ac 50Hz supply APPLIANCE GAS SUPPLY: Natural gas 1. 0 kPa - Universal LPG 2. 75 kPa NOZZLE NOMINAL NOMINAL MARKS GAS PRESSURE 1/100 mm CONSUMPTION kPa MJ/h 1. 50 1. 11 0. 89 0. 93 0. 71 0. 55 11. 00 6. 80 3. 80 11. 00 6. 30 3. 80 1. 00 Burner Auxiliary Semi-rapid Rapid Dia. Tap By-pass 1/100 mm 28 35 42 Cut Out dimensions Width:. TYPE OF GAS TYPE OF BURNER Rapid (large) NATURAL Semi-rapid (medium) GAS Auxiliary (small) U-LPG Rapid (large) Semi-rapid (medium) Auxiliary (small) Aeration adjustment none 2. 75 Important safety requirements Location Choose a location free of draughts and open doors and clear of combustible materials or other fire hazards such as curtains, etc. The location should ensure convenience of operation and service. Any adjacent wall surface situated within 200mm from the edge of any hob burner and above the height of the hob must be a suitable non-combustible material for a height of 150 mm for the entire depth and width of the cooker. Any combustible material above the hotplate must be at least 650 mm above the top of the hob and no construction shall be within 450 mm above the top of the burner. must be left between the side edges of the hob and any adjacent cabinets or walls. FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE 600 mm 700 mm 400 mm 55 mm 400 mm 100 mm 50 m m 50 m m FO 2369* FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 600 mm 700 mm 400 mm 55 mm 400 mm 100 mm 50 m m 50 m m FO 2231* 6 Installation Important This appliance must be installed by qualified personnel. The installer shall verify the satisfactory operation of the ignition system on all burners both individually and in combination. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the furniture unit. The appliance is supplied with a connection cable provided with a plug, able to support the load marked on the identification plate. The plug has to be fitted in a proper socket. If connecting the appliance directly to the electric system, it is necessary that you install a double pole switch between the appliance and the electricity supply, with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current rules. The connection cable has to be placed in order that, in each part, it cannot reach a temperature 50 °C higher than the room temperature. The brown coloured phase cable (fitted in the terminal block contact marked with "L") must always be connected to the network phase. Adaptation to different types of gas WARNING: Servicing shall only be carried out by authorised personnel. Substitution of the nozzles Remove all pan supports, burner caps, rings and crowns; - With a tubular spanner no. 7 unscrew and remove (see diagram) the nozzles substituting them with those corresponding to the type of gas used (see Technical data); - Remount the parts carrying out the operations described in reverse. Upon completion remove existing gas type label and stick the relevant gas type label near the gas supply pipe. If the pressure of gas used is different (or variable) from that foreseen an appropriate pressure regulator should be installed on the entry tube. [. . . ] 12 This warranty applies only to the original buyer. 13 This warranty is the only express warranty given by the Company. 14 If you are the original buyer, please keep your proof of purchase, which will be required, if you request service under this warranty. 15 The Warranty Period is only applicable when your appliance is used at home by you and your family as consumers. [. . . ]