User manual AEG-ELECTROLUX EGG76X

[. . . ] EGG 76 35678-3002 AU Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our local Customer Care Department Installation l l l l l This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant Australian Standards. Any gas installation must be carried out by a registered installer. Remove all packaging before using the hob. [. . . ] must be left between the side edges of the hob and any adjacent cabinets or walls. FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE 600 mm 700 mm 400 mm 55 mm 400 mm 100 mm 50 m m 50 m m FO 2369* FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 600 mm 700 mm 400 mm 55 mm 400 mm 100 mm 50 m m 50 m m FO 2231* 6 Installation Important This appliance must be installed by qualified personnel. The installer shall verify the satisfactory operation of the ignition system on all burners both individually and in combination. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. FO 0814 Regulations This appliance shall be installed in accordance with the manufacturers installation instructions, local gas fitting regulations, municipal building codes, AS5601 (AG601) and any other relevant statutory regulations. FO 0264 A) End of shaft with nut B) Washer C) Elbow Data label The data label is located on the bottom of the hob. This appliance is suitable for Natural or Universal LPG. Ensure that the gas supply matches the data label. A duplicate of the data label is supplied in the packaging of the user manual and must be attached to readily accessible adjacent surfaces of the appliances. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. Natural gas appliances must be fitted with a pressure regulator and be installed at the inlet connection. The gas pressure must then be set as a part of the commissioning procedures. For U-LPG the pressure adjustment is made via the regulator fitted at the domestic cylinder. The natural gas regulator and U-LPG pressure test point must be accessible with the appliance installed. Connection to the gas supply Gas connection must be carried out in conformity with the regulations in force. The appliance leaves the factory tested and regulated for the type of gas indicated on the plate which is situated in the lower position near the gas connection tube. Ascertain that the type of gas with which the appliance will be supplied is the same as that indicated on the plate. If different carry out all the operations according to the indications cited in the paragraph adaption to different types of gas. For a maximum output and minimum consumption ascertain that the pressure of the gas used has the values indicated in the table of burner characteristics. The joint is mounted on the intake area of the pipe, fitted with a filleted nut G 1/2", between the sealing components. Screw the parts without forcing, turn the joint in the direction required and then tighten everything. Important Upon completion of installation, always check: l that all the joints are completely sealed by using a soapy solution, never a flame; l that the gas pressure has been regulated to 1. 00kPa for Natural Gas and 2. 75kPa for Universal-LPG. The pressure test point is located on the regulator. The pressure should be measured and adjusted with the Wok burner on high flame; l that the automatic ignition system is operating satisfactory on all burners, both individually and in combination; l that the burners operate correctly, are stable, without yellow tipping or excessive noise on high and low flame. Then demonstrate to the customer the appliance operation and leave these instructions. Connection Carry out the connection to the gas plant only by means of a rigid metallic pipe conforming to the regulations in force. This appliance is not suitable for connection with a hose assembly. [. . . ] 16 Use of this appliance for commercial purposes is covered by this warranty for a period of 3 months from the date of purchase. FOR SERVICE IN AUSTRALIA PLEASE CALL 13 13 49 FOR SPARE PARTS IN AUSTRALIA PLEASE CALL 13 13 50 10 ELECTROLUX APPLIANCE WARRANTY NEW ZEALAND This appliance is warranted by Electrolux Home Products (NZ) Ltd (the Company) from the date of purchase. The following terms and conditions apply: 1 The Company or its Authorised Service Centre will pay the cost of repairing or replacing all parts of the appliance which the Company or its Authorised Service Centre find defective for a period of 24 months following the date of purchase (the Warranty Period). 2 During the Warranty Period the Company or its Authorised Service Centre, will pay the cost of repairing or replacing all parts, which they find are defective. [. . . ]